forked from mfulz_github/qmk_firmware
Add new Audio Class Driver Host demos.
Fix errors in the new Audio Host mode Class Driver, which would have prevented data from being sent or received properly by the device. Add microphone/square wave generation compile time switch to the Low Level AudioOutput Host demo.
This commit is contained in:
Dean Camera
parent
0bf5064aec
commit
1f1d0710f3
|
|
@ -98,7 +98,7 @@ ISR(TIMER0_COMPA_vect, ISR_BLOCK)
|
|||
{
|
||||
uint8_t PrevEndpoint = Endpoint_GetCurrentEndpoint();
|
||||
|
||||
/* Check if the sample reload timer period has elapsed, and that the USB bus is ready for a new sample */
|
||||
/* Check that the USB bus is ready for the next sample to write */
|
||||
if (Audio_Device_IsReadyForNextSample(&Microphone_Audio_Interface))
|
||||
{
|
||||
int16_t AudioSample;
|
||||
|
|
|
|||
|
|
@ -91,7 +91,8 @@ void SetupHardware(void)
|
|||
ISR(TIMER0_COMPA_vect, ISR_BLOCK)
|
||||
{
|
||||
uint8_t PrevEndpoint = Endpoint_GetCurrentEndpoint();
|
||||
|
||||
|
||||
/* Check that the USB bus is ready for the next sample to read */
|
||||
if (Audio_Device_IsSampleReceived(&Speaker_Audio_Interface))
|
||||
{
|
||||
/* Retrieve the signed 16-bit left and right audio samples, convert to 8-bit */
|
||||
|
|
|
|||
|
|
@ -0,0 +1,248 @@
|
|||
/*
|
||||
LUFA Library
|
||||
Copyright (C) Dean Camera, 2011.
|
||||
|
||||
dean [at] fourwalledcubicle [dot] com
|
||||
www.lufa-lib.org
|
||||
*/
|
||||
|
||||
/*
|
||||
Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
|
||||
|
||||
Permission to use, copy, modify, distribute, and sell this
|
||||
software and its documentation for any purpose is hereby granted
|
||||
without fee, provided that the above copyright notice appear in
|
||||
all copies and that both that the copyright notice and this
|
||||
permission notice and warranty disclaimer appear in supporting
|
||||
documentation, and that the name of the author not be used in
|
||||
advertising or publicity pertaining to distribution of the
|
||||
software without specific, written prior permission.
|
||||
|
||||
The author disclaim all warranties with regard to this
|
||||
software, including all implied warranties of merchantability
|
||||
and fitness. In no event shall the author be liable for any
|
||||
special, indirect or consequential damages or any damages
|
||||
whatsoever resulting from loss of use, data or profits, whether
|
||||
in an action of contract, negligence or other tortious action,
|
||||
arising out of or in connection with the use or performance of
|
||||
this software.
|
||||
*/
|
||||
|
||||
/** \file
|
||||
*
|
||||
* Main source file for the AudioInputHost demo. This file contains the main tasks of
|
||||
* the demo and is responsible for the initial application hardware configuration.
|
||||
*/
|
||||
|
||||
#include "AudioInputHost.h"
|
||||
|
||||
/** LUFA Audio Class driver interface configuration and state information. This structure is
|
||||
* passed to all Audio Class driver functions, so that multiple instances of the same class
|
||||
* within a device can be differentiated from one another.
|
||||
*/
|
||||
USB_ClassInfo_Audio_Host_t Microphone_Audio_Interface =
|
||||
{
|
||||
.Config =
|
||||
{
|
||||
.DataINPipeNumber = 1,
|
||||
},
|
||||
};
|
||||
|
||||
|
||||
/** Main program entry point. This routine configures the hardware required by the application, then
|
||||
* enters a loop to run the application tasks in sequence.
|
||||
*/
|
||||
int main(void)
|
||||
{
|
||||
SetupHardware();
|
||||
|
||||
puts_P(PSTR(ESC_FG_CYAN "Audio Input Host Demo running.\r\n" ESC_FG_WHITE));
|
||||
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
|
||||
sei();
|
||||
|
||||
for (;;)
|
||||
{
|
||||
switch (USB_HostState)
|
||||
{
|
||||
case HOST_STATE_Addressed:
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
|
||||
|
||||
uint16_t ConfigDescriptorSize;
|
||||
uint8_t ConfigDescriptorData[512];
|
||||
|
||||
if (USB_Host_GetDeviceConfigDescriptor(1, &ConfigDescriptorSize, ConfigDescriptorData,
|
||||
sizeof(ConfigDescriptorData)) != HOST_GETCONFIG_Successful)
|
||||
{
|
||||
puts_P(PSTR("Error Retrieving Configuration Descriptor.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
if (Audio_Host_ConfigurePipes(&Microphone_Audio_Interface,
|
||||
ConfigDescriptorSize, ConfigDescriptorData) != AUDIO_ENUMERROR_NoError)
|
||||
{
|
||||
puts_P(PSTR("Attached Device Not a Valid Audio Input Device.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
if (USB_Host_SetDeviceConfiguration(1) != HOST_SENDCONTROL_Successful)
|
||||
{
|
||||
puts_P(PSTR("Error Setting Device Configuration.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
if (Audio_Host_StartStopStreaming(&Microphone_Audio_Interface, true) != HOST_SENDCONTROL_Successful)
|
||||
{
|
||||
puts_P(PSTR("Error Enabling Audio Stream.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
USB_Audio_SampleFreq_t SampleRate = AUDIO_SAMPLE_FREQ(48000);
|
||||
if (Audio_GetSetEndpointProperty(&Microphone_Audio_Interface, Microphone_Audio_Interface.Config.DataINPipeNumber,
|
||||
AUDIO_REQ_SetCurrent, AUDIO_EPCONTROL_SamplingFreq,
|
||||
sizeof(SampleRate), &SampleRate) != HOST_SENDCONTROL_Successful)
|
||||
{
|
||||
puts_P(PSTR("Error Setting Audio Sampling Frequency.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
/* Sample reload timer initialization */
|
||||
TIMSK0 = (1 << OCIE0A);
|
||||
OCR0A = ((F_CPU / 8 / 48000) - 1);
|
||||
TCCR0A = (1 << WGM01); // CTC mode
|
||||
TCCR0B = (1 << CS01); // Fcpu/8 speed
|
||||
|
||||
/* Set speaker as output */
|
||||
DDRC |= (1 << 6);
|
||||
|
||||
/* PWM speaker timer initialization */
|
||||
TCCR3A = ((1 << WGM30) | (1 << COM3A1) | (1 << COM3A0)); // Set on match, clear on TOP
|
||||
TCCR3B = ((1 << WGM32) | (1 << CS30)); // Fast 8-Bit PWM, F_CPU speed
|
||||
|
||||
puts_P(PSTR("Audio Device Enumerated.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_READY);
|
||||
USB_HostState = HOST_STATE_Configured;
|
||||
break;
|
||||
case HOST_STATE_Configured:
|
||||
/* Do nothing - audio stream is handled by the timer interrupt routine */
|
||||
break;
|
||||
}
|
||||
|
||||
Audio_Host_USBTask(&Microphone_Audio_Interface);
|
||||
USB_USBTask();
|
||||
}
|
||||
}
|
||||
|
||||
/** ISR to handle the reloading of the PWM timer with the next sample. */
|
||||
ISR(TIMER0_COMPA_vect, ISR_BLOCK)
|
||||
{
|
||||
uint8_t PrevPipe = Pipe_GetCurrentPipe();
|
||||
|
||||
/* Check that the USB bus is ready for the next sample to read */
|
||||
if (Audio_Host_IsSampleReceived(&Microphone_Audio_Interface))
|
||||
{
|
||||
/* Retrieve the signed 16-bit audio sample, convert to 8-bit */
|
||||
int8_t Sample_8Bit = (Audio_Host_ReadSample16(&Microphone_Audio_Interface) >> 8);
|
||||
|
||||
/* Load the sample into the PWM timer channel */
|
||||
OCR3A = (Sample_8Bit ^ (1 << 7));
|
||||
|
||||
uint8_t LEDMask = LEDS_NO_LEDS;
|
||||
|
||||
/* Turn on LEDs as the sample amplitude increases */
|
||||
if (Sample_8Bit > 16)
|
||||
LEDMask = (LEDS_LED1 | LEDS_LED2 | LEDS_LED3 | LEDS_LED4);
|
||||
else if (Sample_8Bit > 8)
|
||||
LEDMask = (LEDS_LED1 | LEDS_LED2 | LEDS_LED3);
|
||||
else if (Sample_8Bit > 4)
|
||||
LEDMask = (LEDS_LED1 | LEDS_LED2);
|
||||
else if (Sample_8Bit > 2)
|
||||
LEDMask = (LEDS_LED1);
|
||||
|
||||
LEDs_SetAllLEDs(LEDMask);
|
||||
}
|
||||
|
||||
Pipe_SelectPipe(PrevPipe);
|
||||
}
|
||||
|
||||
/** Configures the board hardware and chip peripherals for the demo's functionality. */
|
||||
void SetupHardware(void)
|
||||
{
|
||||
/* Disable watchdog if enabled by bootloader/fuses */
|
||||
MCUSR &= ~(1 << WDRF);
|
||||
wdt_disable();
|
||||
|
||||
/* Disable clock division */
|
||||
clock_prescale_set(clock_div_1);
|
||||
|
||||
/* Hardware Initialization */
|
||||
Serial_Init(9600, false);
|
||||
LEDs_Init();
|
||||
USB_Init();
|
||||
|
||||
/* Create a stdio stream for the serial port for stdin and stdout */
|
||||
Serial_CreateStream(NULL);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_DeviceAttached event. This indicates that a device has been attached to the host, and
|
||||
* starts the library USB task to begin the enumeration and USB management process.
|
||||
*/
|
||||
void EVENT_USB_Host_DeviceAttached(void)
|
||||
{
|
||||
puts_P(PSTR("Device Attached.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_DeviceUnattached event. This indicates that a device has been removed from the host, and
|
||||
* stops the library USB task management process.
|
||||
*/
|
||||
void EVENT_USB_Host_DeviceUnattached(void)
|
||||
{
|
||||
puts_P(PSTR("\r\nDevice Unattached.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_DeviceEnumerationComplete event. This indicates that a device has been successfully
|
||||
* enumerated by the host and is now ready to be used by the application.
|
||||
*/
|
||||
void EVENT_USB_Host_DeviceEnumerationComplete(void)
|
||||
{
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_READY);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_HostError event. This indicates that a hardware error occurred while in host mode. */
|
||||
void EVENT_USB_Host_HostError(const uint8_t ErrorCode)
|
||||
{
|
||||
USB_Disable();
|
||||
|
||||
printf_P(PSTR(ESC_FG_RED "Host Mode Error\r\n"
|
||||
" -- Error Code %d\r\n" ESC_FG_WHITE), ErrorCode);
|
||||
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
for(;;);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_DeviceEnumerationFailed event. This indicates that a problem occurred while
|
||||
* enumerating an attached USB device.
|
||||
*/
|
||||
void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode,
|
||||
const uint8_t SubErrorCode)
|
||||
{
|
||||
printf_P(PSTR(ESC_FG_RED "Dev Enum Error\r\n"
|
||||
" -- Error Code %d\r\n"
|
||||
" -- Sub Error Code %d\r\n"
|
||||
" -- In State %d\r\n" ESC_FG_WHITE), ErrorCode, SubErrorCode, USB_HostState);
|
||||
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
}
|
||||
|
||||
|
|
@ -0,0 +1,77 @@
|
|||
/*
|
||||
LUFA Library
|
||||
Copyright (C) Dean Camera, 2011.
|
||||
|
||||
dean [at] fourwalledcubicle [dot] com
|
||||
www.lufa-lib.org
|
||||
*/
|
||||
|
||||
/*
|
||||
Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
|
||||
|
||||
Permission to use, copy, modify, distribute, and sell this
|
||||
software and its documentation for any purpose is hereby granted
|
||||
without fee, provided that the above copyright notice appear in
|
||||
all copies and that both that the copyright notice and this
|
||||
permission notice and warranty disclaimer appear in supporting
|
||||
documentation, and that the name of the author not be used in
|
||||
advertising or publicity pertaining to distribution of the
|
||||
software without specific, written prior permission.
|
||||
|
||||
The author disclaim all warranties with regard to this
|
||||
software, including all implied warranties of merchantability
|
||||
and fitness. In no event shall the author be liable for any
|
||||
special, indirect or consequential damages or any damages
|
||||
whatsoever resulting from loss of use, data or profits, whether
|
||||
in an action of contract, negligence or other tortious action,
|
||||
arising out of or in connection with the use or performance of
|
||||
this software.
|
||||
*/
|
||||
|
||||
/** \file
|
||||
*
|
||||
* Header file for AudioInputHost.c.
|
||||
*/
|
||||
|
||||
#ifndef _AUDIO_INPUT_HOST_H_
|
||||
#define _AUDIO_INPUT_HOST_H_
|
||||
|
||||
/* Includes: */
|
||||
#include <avr/io.h>
|
||||
#include <avr/wdt.h>
|
||||
#include <avr/pgmspace.h>
|
||||
#include <avr/power.h>
|
||||
#include <avr/interrupt.h>
|
||||
#include <stdio.h>
|
||||
|
||||
#include <LUFA/Version.h>
|
||||
#include <LUFA/Drivers/Misc/TerminalCodes.h>
|
||||
#include <LUFA/Drivers/Peripheral/Serial.h>
|
||||
#include <LUFA/Drivers/Board/LEDs.h>
|
||||
#include <LUFA/Drivers/USB/USB.h>
|
||||
|
||||
/* Macros: */
|
||||
/** LED mask for the library LED driver, to indicate that the USB interface is not ready. */
|
||||
#define LEDMASK_USB_NOTREADY LEDS_LED1
|
||||
|
||||
/** LED mask for the library LED driver, to indicate that the USB interface is enumerating. */
|
||||
#define LEDMASK_USB_ENUMERATING (LEDS_LED2 | LEDS_LED3)
|
||||
|
||||
/** LED mask for the library LED driver, to indicate that the USB interface is ready. */
|
||||
#define LEDMASK_USB_READY (LEDS_LED2 | LEDS_LED4)
|
||||
|
||||
/** LED mask for the library LED driver, to indicate that an error has occurred in the USB interface. */
|
||||
#define LEDMASK_USB_ERROR (LEDS_LED1 | LEDS_LED3)
|
||||
|
||||
/* Function Prototypes: */
|
||||
void SetupHardware(void);
|
||||
|
||||
void EVENT_USB_Host_HostError(const uint8_t ErrorCode);
|
||||
void EVENT_USB_Host_DeviceAttached(void);
|
||||
void EVENT_USB_Host_DeviceUnattached(void);
|
||||
void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode,
|
||||
const uint8_t SubErrorCode);
|
||||
void EVENT_USB_Host_DeviceEnumerationComplete(void);
|
||||
|
||||
#endif
|
||||
|
||||
File diff suppressed because it is too large
Load Diff
|
|
@ -0,0 +1,714 @@
|
|||
# Hey Emacs, this is a -*- makefile -*-
|
||||
#----------------------------------------------------------------------------
|
||||
# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
|
||||
# >> Modified for use with the LUFA project. <<
|
||||
#
|
||||
# Released to the Public Domain
|
||||
#
|
||||
# Additional material for this makefile was written by:
|
||||
# Peter Fleury
|
||||
# Tim Henigan
|
||||
# Colin O'Flynn
|
||||
# Reiner Patommel
|
||||
# Markus Pfaff
|
||||
# Sander Pool
|
||||
# Frederik Rouleau
|
||||
# Carlos Lamas
|
||||
# Dean Camera
|
||||
# Opendous Inc.
|
||||
# Denver Gingerich
|
||||
#
|
||||
#----------------------------------------------------------------------------
|
||||
# On command line:
|
||||
#
|
||||
# make all = Make software.
|
||||
#
|
||||
# make clean = Clean out built project files.
|
||||
#
|
||||
# make coff = Convert ELF to AVR COFF.
|
||||
#
|
||||
# make extcoff = Convert ELF to AVR Extended COFF.
|
||||
#
|
||||
# make program = Download the hex file to the device, using avrdude.
|
||||
# Please customize the avrdude settings below first!
|
||||
#
|
||||
# make dfu = Download the hex file to the device, using dfu-programmer (must
|
||||
# have dfu-programmer installed).
|
||||
#
|
||||
# make flip = Download the hex file to the device, using Atmel FLIP (must
|
||||
# have Atmel FLIP installed).
|
||||
#
|
||||
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
|
||||
# (must have dfu-programmer installed).
|
||||
#
|
||||
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
|
||||
# (must have Atmel FLIP installed).
|
||||
#
|
||||
# make doxygen = Generate DoxyGen documentation for the project (must have
|
||||
# DoxyGen installed)
|
||||
#
|
||||
# make debug = Start either simulavr or avarice as specified for debugging,
|
||||
# with avr-gdb or avr-insight as the front end for debugging.
|
||||
#
|
||||
# make filename.s = Just compile filename.c into the assembler code only.
|
||||
#
|
||||
# make filename.i = Create a preprocessed source file for use in submitting
|
||||
# bug reports to the GCC project.
|
||||
#
|
||||
# To rebuild project do "make clean" then "make all".
|
||||
#----------------------------------------------------------------------------
|
||||
|
||||
|
||||
# MCU name
|
||||
MCU = at90usb1287
|
||||
|
||||
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
|
||||
# Target board (see library "Board Types" documentation, NONE for projects not requiring
|
||||
# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
|
||||
# "Board" inside the application directory.
|
||||
BOARD = USBKEY
|
||||
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 8000000
|
||||
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
|
||||
# Output format. (can be srec, ihex, binary)
|
||||
FORMAT = ihex
|
||||
|
||||
|
||||
# Target file name (without extension).
|
||||
TARGET = AudioInputHost
|
||||
|
||||
|
||||
# Object files directory
|
||||
# To put object files in current directory, use a dot (.), do NOT make
|
||||
# this an empty or blank macro!
|
||||
OBJDIR = .
|
||||
|
||||
|
||||
# Path to the LUFA library
|
||||
LUFA_PATH = ../../../..
|
||||
|
||||
|
||||
# LUFA library compile-time options and predefined tokens
|
||||
LUFA_OPTS = -D USB_HOST_ONLY
|
||||
LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
|
||||
|
||||
|
||||
# Create the LUFA source path variables by including the LUFA root makefile
|
||||
include $(LUFA_PATH)/LUFA/makefile
|
||||
|
||||
|
||||
# List C source files here. (C dependencies are automatically generated.)
|
||||
SRC = $(TARGET).c \
|
||||
$(LUFA_SRC_USB) \
|
||||
$(LUFA_SRC_USBCLASS) \
|
||||
$(LUFA_SRC_SERIAL)
|
||||
|
||||
|
||||
# List C++ source files here. (C dependencies are automatically generated.)
|
||||
CPPSRC =
|
||||
|
||||
|
||||
# List Assembler source files here.
|
||||
# Make them always end in a capital .S. Files ending in a lowercase .s
|
||||
# will not be considered source files but generated files (assembler
|
||||
# output from the compiler), and will be deleted upon "make clean"!
|
||||
# Even though the DOS/Win* filesystem matches both .s and .S the same,
|
||||
# it will preserve the spelling of the filenames, and gcc itself does
|
||||
# care about how the name is spelled on its command-line.
|
||||
ASRC =
|
||||
|
||||
|
||||
# Optimization level, can be [0, 1, 2, 3, s].
|
||||
# 0 = turn off optimization. s = optimize for size.
|
||||
# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
|
||||
OPT = s
|
||||
|
||||
|
||||
# Debugging format.
|
||||
# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
|
||||
# AVR Studio 4.10 requires dwarf-2.
|
||||
# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
|
||||
DEBUG = dwarf-2
|
||||
|
||||
|
||||
# List any extra directories to look for include files here.
|
||||
# Each directory must be seperated by a space.
|
||||
# Use forward slashes for directory separators.
|
||||
# For a directory that has spaces, enclose it in quotes.
|
||||
EXTRAINCDIRS = $(LUFA_PATH)/
|
||||
|
||||
|
||||
# Compiler flag to set the C Standard level.
|
||||
# c89 = "ANSI" C
|
||||
# gnu89 = c89 plus GCC extensions
|
||||
# c99 = ISO C99 standard (not yet fully implemented)
|
||||
# gnu99 = c99 plus GCC extensions
|
||||
CSTANDARD = -std=c99
|
||||
|
||||
|
||||
# Place -D or -U options here for C sources
|
||||
CDEFS = -DF_CPU=$(F_CPU)UL
|
||||
CDEFS += -DF_USB=$(F_USB)UL
|
||||
CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
|
||||
CDEFS += $(LUFA_OPTS)
|
||||
|
||||
|
||||
# Place -D or -U options here for ASM sources
|
||||
ADEFS = -DF_CPU=$(F_CPU)
|
||||
ADEFS += -DF_USB=$(F_USB)UL
|
||||
ADEFS += -DBOARD=BOARD_$(BOARD)
|
||||
ADEFS += $(LUFA_OPTS)
|
||||
|
||||
# Place -D or -U options here for C++ sources
|
||||
CPPDEFS = -DF_CPU=$(F_CPU)UL
|
||||
CPPDEFS += -DF_USB=$(F_USB)UL
|
||||
CPPDEFS += -DBOARD=BOARD_$(BOARD)
|
||||
CPPDEFS += $(LUFA_OPTS)
|
||||
#CPPDEFS += -D__STDC_LIMIT_MACROS
|
||||
#CPPDEFS += -D__STDC_CONSTANT_MACROS
|
||||
|
||||
|
||||
|
||||
#---------------- Compiler Options C ----------------
|
||||
# -g*: generate debugging information
|
||||
# -O*: optimization level
|
||||
# -f...: tuning, see GCC manual and avr-libc documentation
|
||||
# -Wall...: warning level
|
||||
# -Wa,...: tell GCC to pass this to the assembler.
|
||||
# -adhlns...: create assembler listing
|
||||
CFLAGS = -g$(DEBUG)
|
||||
CFLAGS += $(CDEFS)
|
||||
CFLAGS += -O$(OPT)
|
||||
CFLAGS += -funsigned-char
|
||||
CFLAGS += -funsigned-bitfields
|
||||
CFLAGS += -ffunction-sections
|
||||
CFLAGS += -fno-inline-small-functions
|
||||
CFLAGS += -fpack-struct
|
||||
CFLAGS += -fshort-enums
|
||||
CFLAGS += -fno-strict-aliasing
|
||||
CFLAGS += -Wall
|
||||
CFLAGS += -Wstrict-prototypes
|
||||
#CFLAGS += -mshort-calls
|
||||
#CFLAGS += -fno-unit-at-a-time
|
||||
#CFLAGS += -Wundef
|
||||
#CFLAGS += -Wunreachable-code
|
||||
#CFLAGS += -Wsign-compare
|
||||
CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
|
||||
CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
|
||||
CFLAGS += $(CSTANDARD)
|
||||
|
||||
|
||||
#---------------- Compiler Options C++ ----------------
|
||||
# -g*: generate debugging information
|
||||
# -O*: optimization level
|
||||
# -f...: tuning, see GCC manual and avr-libc documentation
|
||||
# -Wall...: warning level
|
||||
# -Wa,...: tell GCC to pass this to the assembler.
|
||||
# -adhlns...: create assembler listing
|
||||
CPPFLAGS = -g$(DEBUG)
|
||||
CPPFLAGS += $(CPPDEFS)
|
||||
CPPFLAGS += -O$(OPT)
|
||||
CPPFLAGS += -funsigned-char
|
||||
CPPFLAGS += -funsigned-bitfields
|
||||
CPPFLAGS += -fpack-struct
|
||||
CPPFLAGS += -fshort-enums
|
||||
CPPFLAGS += -fno-exceptions
|
||||
CPPFLAGS += -Wall
|
||||
CPPFLAGS += -Wundef
|
||||
#CPPFLAGS += -mshort-calls
|
||||
#CPPFLAGS += -fno-unit-at-a-time
|
||||
#CPPFLAGS += -Wstrict-prototypes
|
||||
#CPPFLAGS += -Wunreachable-code
|
||||
#CPPFLAGS += -Wsign-compare
|
||||
CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
|
||||
CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
|
||||
#CPPFLAGS += $(CSTANDARD)
|
||||
|
||||
|
||||
#---------------- Assembler Options ----------------
|
||||
# -Wa,...: tell GCC to pass this to the assembler.
|
||||
# -adhlns: create listing
|
||||
# -gstabs: have the assembler create line number information; note that
|
||||
# for use in COFF files, additional information about filenames
|
||||
# and function names needs to be present in the assembler source
|
||||
# files -- see avr-libc docs [FIXME: not yet described there]
|
||||
# -listing-cont-lines: Sets the maximum number of continuation lines of hex
|
||||
# dump that will be displayed for a given single line of source input.
|
||||
ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
|
||||
|
||||
|
||||
#---------------- Library Options ----------------
|
||||
# Minimalistic printf version
|
||||
PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
|
||||
|
||||
# Floating point printf version (requires MATH_LIB = -lm below)
|
||||
PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
|
||||
|
||||
# If this is left blank, then it will use the Standard printf version.
|
||||
PRINTF_LIB =
|
||||
#PRINTF_LIB = $(PRINTF_LIB_MIN)
|
||||
#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
|
||||
|
||||
|
||||
# Minimalistic scanf version
|
||||
SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
|
||||
|
||||
# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
|
||||
SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
|
||||
|
||||
# If this is left blank, then it will use the Standard scanf version.
|
||||
SCANF_LIB =
|
||||
#SCANF_LIB = $(SCANF_LIB_MIN)
|
||||
#SCANF_LIB = $(SCANF_LIB_FLOAT)
|
||||
|
||||
|
||||
MATH_LIB = -lm
|
||||
|
||||
|
||||
# List any extra directories to look for libraries here.
|
||||
# Each directory must be seperated by a space.
|
||||
# Use forward slashes for directory separators.
|
||||
# For a directory that has spaces, enclose it in quotes.
|
||||
EXTRALIBDIRS =
|
||||
|
||||
|
||||
|
||||
#---------------- External Memory Options ----------------
|
||||
|
||||
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
|
||||
# used for variables (.data/.bss) and heap (malloc()).
|
||||
#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
|
||||
|
||||
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
|
||||
# only used for heap (malloc()).
|
||||
#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
|
||||
|
||||
EXTMEMOPTS =
|
||||
|
||||
|
||||
|
||||
#---------------- Linker Options ----------------
|
||||
# -Wl,...: tell GCC to pass this to linker.
|
||||
# -Map: create map file
|
||||
# --cref: add cross reference to map file
|
||||
LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
|
||||
LDFLAGS += -Wl,--relax
|
||||
LDFLAGS += -Wl,--gc-sections
|
||||
LDFLAGS += $(EXTMEMOPTS)
|
||||
LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
|
||||
LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
|
||||
#LDFLAGS += -T linker_script.x
|
||||
|
||||
|
||||
|
||||
#---------------- Programming Options (avrdude) ----------------
|
||||
|
||||
# Programming hardware
|
||||
# Type: avrdude -c ?
|
||||
# to get a full listing.
|
||||
#
|
||||
AVRDUDE_PROGRAMMER = jtagmkII
|
||||
|
||||
# com1 = serial port. Use lpt1 to connect to parallel port.
|
||||
AVRDUDE_PORT = usb
|
||||
|
||||
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
|
||||
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
|
||||
|
||||
|
||||
# Uncomment the following if you want avrdude's erase cycle counter.
|
||||
# Note that this counter needs to be initialized first using -Yn,
|
||||
# see avrdude manual.
|
||||
#AVRDUDE_ERASE_COUNTER = -y
|
||||
|
||||
# Uncomment the following if you do /not/ wish a verification to be
|
||||
# performed after programming the device.
|
||||
#AVRDUDE_NO_VERIFY = -V
|
||||
|
||||
# Increase verbosity level. Please use this when submitting bug
|
||||
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
|
||||
# to submit bug reports.
|
||||
#AVRDUDE_VERBOSE = -v -v
|
||||
|
||||
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
|
||||
|
||||
|
||||
|
||||
#---------------- Debugging Options ----------------
|
||||
|
||||
# For simulavr only - target MCU frequency.
|
||||
DEBUG_MFREQ = $(F_CPU)
|
||||
|
||||
# Set the DEBUG_UI to either gdb or insight.
|
||||
# DEBUG_UI = gdb
|
||||
DEBUG_UI = insight
|
||||
|
||||
# Set the debugging back-end to either avarice, simulavr.
|
||||
DEBUG_BACKEND = avarice
|
||||
#DEBUG_BACKEND = simulavr
|
||||
|
||||
# GDB Init Filename.
|
||||
GDBINIT_FILE = __avr_gdbinit
|
||||
|
||||
# When using avarice settings for the JTAG
|
||||
JTAG_DEV = /dev/com1
|
||||
|
||||
# Debugging port used to communicate between GDB / avarice / simulavr.
|
||||
DEBUG_PORT = 4242
|
||||
|
||||
# Debugging host used to communicate between GDB / avarice / simulavr, normally
|
||||
# just set to localhost unless doing some sort of crazy debugging when
|
||||
# avarice is running on a different computer.
|
||||
DEBUG_HOST = localhost
|
||||
|
||||
|
||||
|
||||
#============================================================================
|
||||
|
||||
|
||||
# Define programs and commands.
|
||||
SHELL = sh
|
||||
CC = avr-gcc
|
||||
OBJCOPY = avr-objcopy
|
||||
OBJDUMP = avr-objdump
|
||||
SIZE = avr-size
|
||||
AR = avr-ar rcs
|
||||
NM = avr-nm
|
||||
AVRDUDE = avrdude
|
||||
REMOVE = rm -f
|
||||
REMOVEDIR = rm -rf
|
||||
COPY = cp
|
||||
WINSHELL = cmd
|
||||
|
||||
|
||||
# Define Messages
|
||||
# English
|
||||
MSG_ERRORS_NONE = Errors: none
|
||||
MSG_BEGIN = -------- begin --------
|
||||
MSG_END = -------- end --------
|
||||
MSG_SIZE_BEFORE = Size before:
|
||||
MSG_SIZE_AFTER = Size after:
|
||||
MSG_COFF = Converting to AVR COFF:
|
||||
MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
|
||||
MSG_FLASH = Creating load file for Flash:
|
||||
MSG_EEPROM = Creating load file for EEPROM:
|
||||
MSG_EXTENDED_LISTING = Creating Extended Listing:
|
||||
MSG_SYMBOL_TABLE = Creating Symbol Table:
|
||||
MSG_LINKING = Linking:
|
||||
MSG_COMPILING = Compiling C:
|
||||
MSG_COMPILING_CPP = Compiling C++:
|
||||
MSG_ASSEMBLING = Assembling:
|
||||
MSG_CLEANING = Cleaning project:
|
||||
MSG_CREATING_LIBRARY = Creating library:
|
||||
|
||||
|
||||
|
||||
|
||||
# Define all object files.
|
||||
OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
|
||||
|
||||
# Define all listing files.
|
||||
LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
|
||||
|
||||
|
||||
# Compiler flags to generate dependency files.
|
||||
GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
|
||||
|
||||
|
||||
# Combine all necessary flags and optional flags.
|
||||
# Add target processor to flags.
|
||||
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
|
||||
ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
|
||||
ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
# Default target.
|
||||
all: begin gccversion sizebefore build sizeafter end
|
||||
|
||||
# Change the build target to build a HEX file or a library.
|
||||
build: elf hex eep lss sym
|
||||
#build: lib
|
||||
|
||||
|
||||
elf: $(TARGET).elf
|
||||
hex: $(TARGET).hex
|
||||
eep: $(TARGET).eep
|
||||
lss: $(TARGET).lss
|
||||
sym: $(TARGET).sym
|
||||
LIBNAME=lib$(TARGET).a
|
||||
lib: $(LIBNAME)
|
||||
|
||||
|
||||
|
||||
# Eye candy.
|
||||
# AVR Studio 3.x does not check make's exit code but relies on
|
||||
# the following magic strings to be generated by the compile job.
|
||||
begin:
|
||||
@echo
|
||||
@echo $(MSG_BEGIN)
|
||||
|
||||
end:
|
||||
@echo $(MSG_END)
|
||||
@echo
|
||||
|
||||
|
||||
# Display size of file.
|
||||
HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
|
||||
ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
|
||||
MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
|
||||
FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
|
||||
|
||||
|
||||
sizebefore:
|
||||
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
|
||||
2>/dev/null; echo; fi
|
||||
|
||||
sizeafter:
|
||||
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
|
||||
2>/dev/null; echo; fi
|
||||
|
||||
|
||||
|
||||
# Display compiler version information.
|
||||
gccversion :
|
||||
@$(CC) --version
|
||||
|
||||
|
||||
# Program the device.
|
||||
program: $(TARGET).hex $(TARGET).eep
|
||||
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
|
||||
|
||||
flip: $(TARGET).hex
|
||||
batchisp -hardware usb -device $(MCU) -operation erase f
|
||||
batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
|
||||
batchisp -hardware usb -device $(MCU) -operation start reset 0
|
||||
|
||||
dfu: $(TARGET).hex
|
||||
dfu-programmer $(MCU) erase
|
||||
dfu-programmer $(MCU) flash $(TARGET).hex
|
||||
dfu-programmer $(MCU) reset
|
||||
|
||||
flip-ee: $(TARGET).hex $(TARGET).eep
|
||||
$(COPY) $(TARGET).eep $(TARGET)eep.hex
|
||||
batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
|
||||
batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
|
||||
batchisp -hardware usb -device $(MCU) -operation start reset 0
|
||||
$(REMOVE) $(TARGET)eep.hex
|
||||
|
||||
dfu-ee: $(TARGET).hex $(TARGET).eep
|
||||
dfu-programmer $(MCU) eeprom-flash $(TARGET).eep
|
||||
dfu-programmer $(MCU) reset
|
||||
|
||||
|
||||
# Generate avr-gdb config/init file which does the following:
|
||||
# define the reset signal, load the target file, connect to target, and set
|
||||
# a breakpoint at main().
|
||||
gdb-config:
|
||||
@$(REMOVE) $(GDBINIT_FILE)
|
||||
@echo define reset >> $(GDBINIT_FILE)
|
||||
@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
|
||||
@echo end >> $(GDBINIT_FILE)
|
||||
@echo file $(TARGET).elf >> $(GDBINIT_FILE)
|
||||
@echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE)
|
||||
ifeq ($(DEBUG_BACKEND),simulavr)
|
||||
@echo load >> $(GDBINIT_FILE)
|
||||
endif
|
||||
@echo break main >> $(GDBINIT_FILE)
|
||||
|
||||
debug: gdb-config $(TARGET).elf
|
||||
ifeq ($(DEBUG_BACKEND), avarice)
|
||||
@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
|
||||
@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
|
||||
$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
|
||||
@$(WINSHELL) /c pause
|
||||
|
||||
else
|
||||
@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
|
||||
$(DEBUG_MFREQ) --port $(DEBUG_PORT)
|
||||
endif
|
||||
@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
|
||||
|
||||
|
||||
|
||||
|
||||
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
|
||||
COFFCONVERT = $(OBJCOPY) --debugging
|
||||
COFFCONVERT += --change-section-address .data-0x800000
|
||||
COFFCONVERT += --change-section-address .bss-0x800000
|
||||
COFFCONVERT += --change-section-address .noinit-0x800000
|
||||
COFFCONVERT += --change-section-address .eeprom-0x810000
|
||||
|
||||
|
||||
|
||||
coff: $(TARGET).elf
|
||||
@echo
|
||||
@echo $(MSG_COFF) $(TARGET).cof
|
||||
$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
|
||||
|
||||
|
||||
extcoff: $(TARGET).elf
|
||||
@echo
|
||||
@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
|
||||
$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
|
||||
|
||||
|
||||
|
||||
# Create final output files (.hex, .eep) from ELF output file.
|
||||
%.hex: %.elf
|
||||
@echo
|
||||
@echo $(MSG_FLASH) $@
|
||||
$(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock $< $@
|
||||
|
||||
%.eep: %.elf
|
||||
@echo
|
||||
@echo $(MSG_EEPROM) $@
|
||||
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
|
||||
--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
|
||||
|
||||
# Create extended listing file from ELF output file.
|
||||
%.lss: %.elf
|
||||
@echo
|
||||
@echo $(MSG_EXTENDED_LISTING) $@
|
||||
$(OBJDUMP) -h -S -z $< > $@
|
||||
|
||||
# Create a symbol table from ELF output file.
|
||||
%.sym: %.elf
|
||||
@echo
|
||||
@echo $(MSG_SYMBOL_TABLE) $@
|
||||
$(NM) -n $< > $@
|
||||
|
||||
|
||||
|
||||
# Create library from object files.
|
||||
.SECONDARY : $(TARGET).a
|
||||
.PRECIOUS : $(OBJ)
|
||||
%.a: $(OBJ)
|
||||
@echo
|
||||
@echo $(MSG_CREATING_LIBRARY) $@
|
||||
$(AR) $@ $(OBJ)
|
||||
|
||||
|
||||
# Link: create ELF output file from object files.
|
||||
.SECONDARY : $(TARGET).elf
|
||||
.PRECIOUS : $(OBJ)
|
||||
%.elf: $(OBJ)
|
||||
@echo
|
||||
@echo $(MSG_LINKING) $@
|
||||
$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
|
||||
|
||||
|
||||
# Compile: create object files from C source files.
|
||||
$(OBJDIR)/%.o : %.c
|
||||
@echo
|
||||
@echo $(MSG_COMPILING) $<
|
||||
$(CC) -c $(ALL_CFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Compile: create object files from C++ source files.
|
||||
$(OBJDIR)/%.o : %.cpp
|
||||
@echo
|
||||
@echo $(MSG_COMPILING_CPP) $<
|
||||
$(CC) -c $(ALL_CPPFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Compile: create assembler files from C source files.
|
||||
%.s : %.c
|
||||
$(CC) -S $(ALL_CFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Compile: create assembler files from C++ source files.
|
||||
%.s : %.cpp
|
||||
$(CC) -S $(ALL_CPPFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Assemble: create object files from assembler source files.
|
||||
$(OBJDIR)/%.o : %.S
|
||||
@echo
|
||||
@echo $(MSG_ASSEMBLING) $<
|
||||
$(CC) -c $(ALL_ASFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Create preprocessed source for use in sending a bug report.
|
||||
%.i : %.c
|
||||
$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Target: clean project.
|
||||
clean: begin clean_list end
|
||||
|
||||
clean_list :
|
||||
@echo
|
||||
@echo $(MSG_CLEANING)
|
||||
$(REMOVE) $(TARGET).hex
|
||||
$(REMOVE) $(TARGET).eep
|
||||
$(REMOVE) $(TARGET).cof
|
||||
$(REMOVE) $(TARGET).elf
|
||||
$(REMOVE) $(TARGET).map
|
||||
$(REMOVE) $(TARGET).sym
|
||||
$(REMOVE) $(TARGET).lss
|
||||
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
|
||||
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
|
||||
$(REMOVE) $(SRC:.c=.s)
|
||||
$(REMOVE) $(SRC:.c=.d)
|
||||
$(REMOVE) $(SRC:.c=.i)
|
||||
$(REMOVEDIR) .dep
|
||||
|
||||
doxygen:
|
||||
@echo Generating Project Documentation...
|
||||
@doxygen Doxygen.conf
|
||||
@echo Documentation Generation Complete.
|
||||
|
||||
clean_doxygen:
|
||||
rm -rf Documentation
|
||||
|
||||
# Create object files directory
|
||||
$(shell mkdir $(OBJDIR) 2>/dev/null)
|
||||
|
||||
|
||||
# Include the dependency files.
|
||||
-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
|
||||
|
||||
|
||||
# Listing of phony targets.
|
||||
.PHONY : all begin finish end sizebefore sizeafter gccversion \
|
||||
build elf hex eep lss sym coff extcoff doxygen clean \
|
||||
clean_list clean_doxygen program dfu flip flip-ee dfu-ee \
|
||||
debug gdb-config
|
||||
|
||||
|
|
@ -0,0 +1,249 @@
|
|||
/*
|
||||
LUFA Library
|
||||
Copyright (C) Dean Camera, 2011.
|
||||
|
||||
dean [at] fourwalledcubicle [dot] com
|
||||
www.lufa-lib.org
|
||||
*/
|
||||
|
||||
/*
|
||||
Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
|
||||
|
||||
Permission to use, copy, modify, distribute, and sell this
|
||||
software and its documentation for any purpose is hereby granted
|
||||
without fee, provided that the above copyright notice appear in
|
||||
all copies and that both that the copyright notice and this
|
||||
permission notice and warranty disclaimer appear in supporting
|
||||
documentation, and that the name of the author not be used in
|
||||
advertising or publicity pertaining to distribution of the
|
||||
software without specific, written prior permission.
|
||||
|
||||
The author disclaim all warranties with regard to this
|
||||
software, including all implied warranties of merchantability
|
||||
and fitness. In no event shall the author be liable for any
|
||||
special, indirect or consequential damages or any damages
|
||||
whatsoever resulting from loss of use, data or profits, whether
|
||||
in an action of contract, negligence or other tortious action,
|
||||
arising out of or in connection with the use or performance of
|
||||
this software.
|
||||
*/
|
||||
|
||||
/** \file
|
||||
*
|
||||
* Main source file for the AudioOutputHost demo. This file contains the main tasks of
|
||||
* the demo and is responsible for the initial application hardware configuration.
|
||||
*/
|
||||
|
||||
#include "AudioOutputHost.h"
|
||||
|
||||
/** LUFA Audio Class driver interface configuration and state information. This structure is
|
||||
* passed to all Audio Class driver functions, so that multiple instances of the same class
|
||||
* within a device can be differentiated from one another.
|
||||
*/
|
||||
USB_ClassInfo_Audio_Host_t Speaker_Audio_Interface =
|
||||
{
|
||||
.Config =
|
||||
{
|
||||
.DataOUTPipeNumber = 1,
|
||||
},
|
||||
};
|
||||
|
||||
|
||||
/** Main program entry point. This routine configures the hardware required by the application, then
|
||||
* enters a loop to run the application tasks in sequence.
|
||||
*/
|
||||
int main(void)
|
||||
{
|
||||
SetupHardware();
|
||||
|
||||
puts_P(PSTR(ESC_FG_CYAN "Audio Output Host Demo running.\r\n" ESC_FG_WHITE));
|
||||
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
|
||||
sei();
|
||||
|
||||
for (;;)
|
||||
{
|
||||
switch (USB_HostState)
|
||||
{
|
||||
case HOST_STATE_Addressed:
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
|
||||
|
||||
uint16_t ConfigDescriptorSize;
|
||||
uint8_t ConfigDescriptorData[512];
|
||||
|
||||
if (USB_Host_GetDeviceConfigDescriptor(1, &ConfigDescriptorSize, ConfigDescriptorData,
|
||||
sizeof(ConfigDescriptorData)) != HOST_GETCONFIG_Successful)
|
||||
{
|
||||
puts_P(PSTR("Error Retrieving Configuration Descriptor.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
if (Audio_Host_ConfigurePipes(&Speaker_Audio_Interface,
|
||||
ConfigDescriptorSize, ConfigDescriptorData) != AUDIO_ENUMERROR_NoError)
|
||||
{
|
||||
puts_P(PSTR("Attached Device Not a Valid Audio Output Device.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
if (USB_Host_SetDeviceConfiguration(1) != HOST_SENDCONTROL_Successful)
|
||||
{
|
||||
puts_P(PSTR("Error Setting Device Configuration.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
if (Audio_Host_StartStopStreaming(&Speaker_Audio_Interface, true) != HOST_SENDCONTROL_Successful)
|
||||
{
|
||||
puts_P(PSTR("Error Enabling Audio Stream.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
USB_Audio_SampleFreq_t SampleRate = AUDIO_SAMPLE_FREQ(48000);
|
||||
if (Audio_GetSetEndpointProperty(&Speaker_Audio_Interface, Speaker_Audio_Interface.Config.DataOUTPipeNumber,
|
||||
AUDIO_REQ_SetCurrent, AUDIO_EPCONTROL_SamplingFreq,
|
||||
sizeof(SampleRate), &SampleRate) != HOST_SENDCONTROL_Successful)
|
||||
{
|
||||
puts_P(PSTR("Error Setting Audio Sampling Frequency.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
|
||||
break;
|
||||
}
|
||||
|
||||
/* Sample reload timer initialization */
|
||||
TIMSK0 = (1 << OCIE0A);
|
||||
OCR0A = ((F_CPU / 8 / 48000) - 1);
|
||||
TCCR0A = (1 << WGM01); // CTC mode
|
||||
TCCR0B = (1 << CS01); // Fcpu/8 speed
|
||||
|
||||
puts_P(PSTR("Audio Device Enumerated.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_READY);
|
||||
USB_HostState = HOST_STATE_Configured;
|
||||
break;
|
||||
case HOST_STATE_Configured:
|
||||
/* Do nothing - audio stream is handled by the timer interrupt routine */
|
||||
break;
|
||||
}
|
||||
|
||||
Audio_Host_USBTask(&Speaker_Audio_Interface);
|
||||
USB_USBTask();
|
||||
}
|
||||
}
|
||||
|
||||
/** ISR to handle the reloading of the PWM timer with the next sample. */
|
||||
ISR(TIMER0_COMPA_vect, ISR_BLOCK)
|
||||
{
|
||||
uint8_t PrevPipe = Pipe_GetCurrentPipe();
|
||||
|
||||
/* Check that the USB bus is ready for the next sample to write */
|
||||
if (Audio_Host_IsReadyForNextSample(&Speaker_Audio_Interface))
|
||||
{
|
||||
int16_t AudioSample;
|
||||
|
||||
#if defined(USE_TEST_TONE)
|
||||
static uint8_t SquareWaveSampleCount;
|
||||
static int16_t CurrentWaveValue;
|
||||
|
||||
/* In test tone mode, generate a square wave at 1/256 of the sample rate */
|
||||
if (SquareWaveSampleCount++ == 0xFF)
|
||||
CurrentWaveValue ^= 0x8000;
|
||||
|
||||
/* Only generate audio if the board button is being pressed */
|
||||
AudioSample = (Buttons_GetStatus() & BUTTONS_BUTTON1) ? CurrentWaveValue : 0;
|
||||
#else
|
||||
/* Audio sample is ADC value scaled to fit the entire range */
|
||||
AudioSample = ((SAMPLE_MAX_RANGE / ADC_MAX_RANGE) * ADC_GetResult());
|
||||
|
||||
#if defined(MICROPHONE_BIASED_TO_HALF_RAIL)
|
||||
/* Microphone is biased to half rail voltage, subtract the bias from the sample value */
|
||||
AudioSample -= (SAMPLE_MAX_RANGE / 2);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
Audio_Host_WriteSample16(&Speaker_Audio_Interface, AudioSample);
|
||||
Audio_Host_WriteSample16(&Speaker_Audio_Interface, AudioSample);
|
||||
}
|
||||
|
||||
Pipe_SelectPipe(PrevPipe);
|
||||
}
|
||||
|
||||
/** Configures the board hardware and chip peripherals for the demo's functionality. */
|
||||
void SetupHardware(void)
|
||||
{
|
||||
/* Disable watchdog if enabled by bootloader/fuses */
|
||||
MCUSR &= ~(1 << WDRF);
|
||||
wdt_disable();
|
||||
|
||||
/* Disable clock division */
|
||||
clock_prescale_set(clock_div_1);
|
||||
|
||||
/* Hardware Initialization */
|
||||
Serial_Init(9600, false);
|
||||
LEDs_Init();
|
||||
Buttons_Init();
|
||||
ADC_Init(ADC_FREE_RUNNING | ADC_PRESCALE_32);
|
||||
ADC_SetupChannel(MIC_IN_ADC_CHANNEL);
|
||||
USB_Init();
|
||||
|
||||
/* Create a stdio stream for the serial port for stdin and stdout */
|
||||
Serial_CreateStream(NULL);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_DeviceAttached event. This indicates that a device has been attached to the host, and
|
||||
* starts the library USB task to begin the enumeration and USB management process.
|
||||
*/
|
||||
void EVENT_USB_Host_DeviceAttached(void)
|
||||
{
|
||||
puts_P(PSTR("Device Attached.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_DeviceUnattached event. This indicates that a device has been removed from the host, and
|
||||
* stops the library USB task management process.
|
||||
*/
|
||||
void EVENT_USB_Host_DeviceUnattached(void)
|
||||
{
|
||||
puts_P(PSTR("\r\nDevice Unattached.\r\n"));
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_DeviceEnumerationComplete event. This indicates that a device has been successfully
|
||||
* enumerated by the host and is now ready to be used by the application.
|
||||
*/
|
||||
void EVENT_USB_Host_DeviceEnumerationComplete(void)
|
||||
{
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_READY);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_HostError event. This indicates that a hardware error occurred while in host mode. */
|
||||
void EVENT_USB_Host_HostError(const uint8_t ErrorCode)
|
||||
{
|
||||
USB_Disable();
|
||||
|
||||
printf_P(PSTR(ESC_FG_RED "Host Mode Error\r\n"
|
||||
" -- Error Code %d\r\n" ESC_FG_WHITE), ErrorCode);
|
||||
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
for(;;);
|
||||
}
|
||||
|
||||
/** Event handler for the USB_DeviceEnumerationFailed event. This indicates that a problem occurred while
|
||||
* enumerating an attached USB device.
|
||||
*/
|
||||
void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode,
|
||||
const uint8_t SubErrorCode)
|
||||
{
|
||||
printf_P(PSTR(ESC_FG_RED "Dev Enum Error\r\n"
|
||||
" -- Error Code %d\r\n"
|
||||
" -- Sub Error Code %d\r\n"
|
||||
" -- In State %d\r\n" ESC_FG_WHITE), ErrorCode, SubErrorCode, USB_HostState);
|
||||
|
||||
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
|
||||
}
|
||||
|
||||
|
|
@ -0,0 +1,91 @@
|
|||
/*
|
||||
LUFA Library
|
||||
Copyright (C) Dean Camera, 2011.
|
||||
|
||||
dean [at] fourwalledcubicle [dot] com
|
||||
www.lufa-lib.org
|
||||
*/
|
||||
|
||||
/*
|
||||
Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
|
||||
|
||||
Permission to use, copy, modify, distribute, and sell this
|
||||
software and its documentation for any purpose is hereby granted
|
||||
without fee, provided that the above copyright notice appear in
|
||||
all copies and that both that the copyright notice and this
|
||||
permission notice and warranty disclaimer appear in supporting
|
||||
documentation, and that the name of the author not be used in
|
||||
advertising or publicity pertaining to distribution of the
|
||||
software without specific, written prior permission.
|
||||
|
||||
The author disclaim all warranties with regard to this
|
||||
software, including all implied warranties of merchantability
|
||||
and fitness. In no event shall the author be liable for any
|
||||
special, indirect or consequential damages or any damages
|
||||
whatsoever resulting from loss of use, data or profits, whether
|
||||
in an action of contract, negligence or other tortious action,
|
||||
arising out of or in connection with the use or performance of
|
||||
this software.
|
||||
*/
|
||||
|
||||
/** \file
|
||||
*
|
||||
* Header file for AudioOutputHost.c.
|
||||
*/
|
||||
|
||||
#ifndef _AUDIO_OUTPUT_HOST_H_
|
||||
#define _AUDIO_OUTPUT_HOST_H_
|
||||
|
||||
/* Includes: */
|
||||
#include <avr/io.h>
|
||||
#include <avr/wdt.h>
|
||||
#include <avr/pgmspace.h>
|
||||
#include <avr/power.h>
|
||||
#include <avr/interrupt.h>
|
||||
#include <stdio.h>
|
||||
|
||||
#include <LUFA/Version.h>
|
||||
#include <LUFA/Drivers/Misc/TerminalCodes.h>
|
||||
#include <LUFA/Drivers/Peripheral/Serial.h>
|
||||
#include <LUFA/Drivers/Peripheral/ADC.h>
|
||||
#include <LUFA/Drivers/Board/LEDs.h>
|
||||
#include <LUFA/Drivers/Board/Buttons.h>
|
||||
#include <LUFA/Drivers/USB/USB.h>
|
||||
|
||||
/* Macros: */
|
||||
/** ADC channel number for the microphone input. */
|
||||
#define MIC_IN_ADC_CHANNEL 2
|
||||
|
||||
/** ADC channel MUX mask for the microphone input. */
|
||||
#define MIC_IN_ADC_MUX_MASK ADC_CHANNEL2
|
||||
|
||||
/** Maximum audio sample value for the microphone input. */
|
||||
#define SAMPLE_MAX_RANGE 0xFFFF
|
||||
|
||||
/** Maximum ADC range for the microphone input. */
|
||||
#define ADC_MAX_RANGE 0x3FF
|
||||
|
||||
/** LED mask for the library LED driver, to indicate that the USB interface is not ready. */
|
||||
#define LEDMASK_USB_NOTREADY LEDS_LED1
|
||||
|
||||
/** LED mask for the library LED driver, to indicate that the USB interface is enumerating. */
|
||||
#define LEDMASK_USB_ENUMERATING (LEDS_LED2 | LEDS_LED3)
|
||||
|
||||
/** LED mask for the library LED driver, to indicate that the USB interface is ready. */
|
||||
#define LEDMASK_USB_READY (LEDS_LED2 | LEDS_LED4)
|
||||
|
||||
/** LED mask for the library LED driver, to indicate that an error has occurred in the USB interface. */
|
||||
#define LEDMASK_USB_ERROR (LEDS_LED1 | LEDS_LED3)
|
||||
|
||||
/* Function Prototypes: */
|
||||
void SetupHardware(void);
|
||||
|
||||
void EVENT_USB_Host_HostError(const uint8_t ErrorCode);
|
||||
void EVENT_USB_Host_DeviceAttached(void);
|
||||
void EVENT_USB_Host_DeviceUnattached(void);
|
||||
void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode,
|
||||
const uint8_t SubErrorCode);
|
||||
void EVENT_USB_Host_DeviceEnumerationComplete(void);
|
||||
|
||||
#endif
|
||||
|
||||
File diff suppressed because it is too large
Load Diff
|
|
@ -0,0 +1,714 @@
|
|||
# Hey Emacs, this is a -*- makefile -*-
|
||||
#----------------------------------------------------------------------------
|
||||
# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
|
||||
# >> Modified for use with the LUFA project. <<
|
||||
#
|
||||
# Released to the Public Domain
|
||||
#
|
||||
# Additional material for this makefile was written by:
|
||||
# Peter Fleury
|
||||
# Tim Henigan
|
||||
# Colin O'Flynn
|
||||
# Reiner Patommel
|
||||
# Markus Pfaff
|
||||
# Sander Pool
|
||||
# Frederik Rouleau
|
||||
# Carlos Lamas
|
||||
# Dean Camera
|
||||
# Opendous Inc.
|
||||
# Denver Gingerich
|
||||
#
|
||||
#----------------------------------------------------------------------------
|
||||
# On command line:
|
||||
#
|
||||
# make all = Make software.
|
||||
#
|
||||
# make clean = Clean out built project files.
|
||||
#
|
||||
# make coff = Convert ELF to AVR COFF.
|
||||
#
|
||||
# make extcoff = Convert ELF to AVR Extended COFF.
|
||||
#
|
||||
# make program = Download the hex file to the device, using avrdude.
|
||||
# Please customize the avrdude settings below first!
|
||||
#
|
||||
# make dfu = Download the hex file to the device, using dfu-programmer (must
|
||||
# have dfu-programmer installed).
|
||||
#
|
||||
# make flip = Download the hex file to the device, using Atmel FLIP (must
|
||||
# have Atmel FLIP installed).
|
||||
#
|
||||
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
|
||||
# (must have dfu-programmer installed).
|
||||
#
|
||||
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
|
||||
# (must have Atmel FLIP installed).
|
||||
#
|
||||
# make doxygen = Generate DoxyGen documentation for the project (must have
|
||||
# DoxyGen installed)
|
||||
#
|
||||
# make debug = Start either simulavr or avarice as specified for debugging,
|
||||
# with avr-gdb or avr-insight as the front end for debugging.
|
||||
#
|
||||
# make filename.s = Just compile filename.c into the assembler code only.
|
||||
#
|
||||
# make filename.i = Create a preprocessed source file for use in submitting
|
||||
# bug reports to the GCC project.
|
||||
#
|
||||
# To rebuild project do "make clean" then "make all".
|
||||
#----------------------------------------------------------------------------
|
||||
|
||||
|
||||
# MCU name
|
||||
MCU = at90usb1287
|
||||
|
||||
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
|
||||
# Target board (see library "Board Types" documentation, NONE for projects not requiring
|
||||
# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
|
||||
# "Board" inside the application directory.
|
||||
BOARD = USBKEY
|
||||
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 8000000
|
||||
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
|
||||
# Output format. (can be srec, ihex, binary)
|
||||
FORMAT = ihex
|
||||
|
||||
|
||||
# Target file name (without extension).
|
||||
TARGET = AudioOutputHost
|
||||
|
||||
|
||||
# Object files directory
|
||||
# To put object files in current directory, use a dot (.), do NOT make
|
||||
# this an empty or blank macro!
|
||||
OBJDIR = .
|
||||
|
||||
|
||||
# Path to the LUFA library
|
||||
LUFA_PATH = ../../../..
|
||||
|
||||
|
||||
# LUFA library compile-time options and predefined tokens
|
||||
LUFA_OPTS = -D USB_HOST_ONLY
|
||||
LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
|
||||
|
||||
|
||||
# Create the LUFA source path variables by including the LUFA root makefile
|
||||
include $(LUFA_PATH)/LUFA/makefile
|
||||
|
||||
|
||||
# List C source files here. (C dependencies are automatically generated.)
|
||||
SRC = $(TARGET).c \
|
||||
$(LUFA_SRC_USB) \
|
||||
$(LUFA_SRC_USBCLASS) \
|
||||
$(LUFA_SRC_SERIAL)
|
||||
|
||||
|
||||
# List C++ source files here. (C dependencies are automatically generated.)
|
||||
CPPSRC =
|
||||
|
||||
|
||||
# List Assembler source files here.
|
||||
# Make them always end in a capital .S. Files ending in a lowercase .s
|
||||
# will not be considered source files but generated files (assembler
|
||||
# output from the compiler), and will be deleted upon "make clean"!
|
||||
# Even though the DOS/Win* filesystem matches both .s and .S the same,
|
||||
# it will preserve the spelling of the filenames, and gcc itself does
|
||||
# care about how the name is spelled on its command-line.
|
||||
ASRC =
|
||||
|
||||
|
||||
# Optimization level, can be [0, 1, 2, 3, s].
|
||||
# 0 = turn off optimization. s = optimize for size.
|
||||
# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
|
||||
OPT = s
|
||||
|
||||
|
||||
# Debugging format.
|
||||
# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
|
||||
# AVR Studio 4.10 requires dwarf-2.
|
||||
# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
|
||||
DEBUG = dwarf-2
|
||||
|
||||
|
||||
# List any extra directories to look for include files here.
|
||||
# Each directory must be seperated by a space.
|
||||
# Use forward slashes for directory separators.
|
||||
# For a directory that has spaces, enclose it in quotes.
|
||||
EXTRAINCDIRS = $(LUFA_PATH)/
|
||||
|
||||
|
||||
# Compiler flag to set the C Standard level.
|
||||
# c89 = "ANSI" C
|
||||
# gnu89 = c89 plus GCC extensions
|
||||
# c99 = ISO C99 standard (not yet fully implemented)
|
||||
# gnu99 = c99 plus GCC extensions
|
||||
CSTANDARD = -std=c99
|
||||
|
||||
|
||||
# Place -D or -U options here for C sources
|
||||
CDEFS = -DF_CPU=$(F_CPU)UL
|
||||
CDEFS += -DF_USB=$(F_USB)UL
|
||||
CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
|
||||
CDEFS += $(LUFA_OPTS)
|
||||
|
||||
|
||||
# Place -D or -U options here for ASM sources
|
||||
ADEFS = -DF_CPU=$(F_CPU)
|
||||
ADEFS += -DF_USB=$(F_USB)UL
|
||||
ADEFS += -DBOARD=BOARD_$(BOARD)
|
||||
ADEFS += $(LUFA_OPTS)
|
||||
|
||||
# Place -D or -U options here for C++ sources
|
||||
CPPDEFS = -DF_CPU=$(F_CPU)UL
|
||||
CPPDEFS += -DF_USB=$(F_USB)UL
|
||||
CPPDEFS += -DBOARD=BOARD_$(BOARD)
|
||||
CPPDEFS += $(LUFA_OPTS)
|
||||
#CPPDEFS += -D__STDC_LIMIT_MACROS
|
||||
#CPPDEFS += -D__STDC_CONSTANT_MACROS
|
||||
|
||||
|
||||
|
||||
#---------------- Compiler Options C ----------------
|
||||
# -g*: generate debugging information
|
||||
# -O*: optimization level
|
||||
# -f...: tuning, see GCC manual and avr-libc documentation
|
||||
# -Wall...: warning level
|
||||
# -Wa,...: tell GCC to pass this to the assembler.
|
||||
# -adhlns...: create assembler listing
|
||||
CFLAGS = -g$(DEBUG)
|
||||
CFLAGS += $(CDEFS)
|
||||
CFLAGS += -O$(OPT)
|
||||
CFLAGS += -funsigned-char
|
||||
CFLAGS += -funsigned-bitfields
|
||||
CFLAGS += -ffunction-sections
|
||||
CFLAGS += -fno-inline-small-functions
|
||||
CFLAGS += -fpack-struct
|
||||
CFLAGS += -fshort-enums
|
||||
CFLAGS += -fno-strict-aliasing
|
||||
CFLAGS += -Wall
|
||||
CFLAGS += -Wstrict-prototypes
|
||||
#CFLAGS += -mshort-calls
|
||||
#CFLAGS += -fno-unit-at-a-time
|
||||
#CFLAGS += -Wundef
|
||||
#CFLAGS += -Wunreachable-code
|
||||
#CFLAGS += -Wsign-compare
|
||||
CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
|
||||
CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
|
||||
CFLAGS += $(CSTANDARD)
|
||||
|
||||
|
||||
#---------------- Compiler Options C++ ----------------
|
||||
# -g*: generate debugging information
|
||||
# -O*: optimization level
|
||||
# -f...: tuning, see GCC manual and avr-libc documentation
|
||||
# -Wall...: warning level
|
||||
# -Wa,...: tell GCC to pass this to the assembler.
|
||||
# -adhlns...: create assembler listing
|
||||
CPPFLAGS = -g$(DEBUG)
|
||||
CPPFLAGS += $(CPPDEFS)
|
||||
CPPFLAGS += -O$(OPT)
|
||||
CPPFLAGS += -funsigned-char
|
||||
CPPFLAGS += -funsigned-bitfields
|
||||
CPPFLAGS += -fpack-struct
|
||||
CPPFLAGS += -fshort-enums
|
||||
CPPFLAGS += -fno-exceptions
|
||||
CPPFLAGS += -Wall
|
||||
CPPFLAGS += -Wundef
|
||||
#CPPFLAGS += -mshort-calls
|
||||
#CPPFLAGS += -fno-unit-at-a-time
|
||||
#CPPFLAGS += -Wstrict-prototypes
|
||||
#CPPFLAGS += -Wunreachable-code
|
||||
#CPPFLAGS += -Wsign-compare
|
||||
CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
|
||||
CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
|
||||
#CPPFLAGS += $(CSTANDARD)
|
||||
|
||||
|
||||
#---------------- Assembler Options ----------------
|
||||
# -Wa,...: tell GCC to pass this to the assembler.
|
||||
# -adhlns: create listing
|
||||
# -gstabs: have the assembler create line number information; note that
|
||||
# for use in COFF files, additional information about filenames
|
||||
# and function names needs to be present in the assembler source
|
||||
# files -- see avr-libc docs [FIXME: not yet described there]
|
||||
# -listing-cont-lines: Sets the maximum number of continuation lines of hex
|
||||
# dump that will be displayed for a given single line of source input.
|
||||
ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
|
||||
|
||||
|
||||
#---------------- Library Options ----------------
|
||||
# Minimalistic printf version
|
||||
PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
|
||||
|
||||
# Floating point printf version (requires MATH_LIB = -lm below)
|
||||
PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
|
||||
|
||||
# If this is left blank, then it will use the Standard printf version.
|
||||
PRINTF_LIB =
|
||||
#PRINTF_LIB = $(PRINTF_LIB_MIN)
|
||||
#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
|
||||
|
||||
|
||||
# Minimalistic scanf version
|
||||
SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
|
||||
|
||||
# Floating point + %[ scanf version (requires MATH_LIB = -lm below)
|
||||
SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
|
||||
|
||||
# If this is left blank, then it will use the Standard scanf version.
|
||||
SCANF_LIB =
|
||||
#SCANF_LIB = $(SCANF_LIB_MIN)
|
||||
#SCANF_LIB = $(SCANF_LIB_FLOAT)
|
||||
|
||||
|
||||
MATH_LIB = -lm
|
||||
|
||||
|
||||
# List any extra directories to look for libraries here.
|
||||
# Each directory must be seperated by a space.
|
||||
# Use forward slashes for directory separators.
|
||||
# For a directory that has spaces, enclose it in quotes.
|
||||
EXTRALIBDIRS =
|
||||
|
||||
|
||||
|
||||
#---------------- External Memory Options ----------------
|
||||
|
||||
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
|
||||
# used for variables (.data/.bss) and heap (malloc()).
|
||||
#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
|
||||
|
||||
# 64 KB of external RAM, starting after internal RAM (ATmega128!),
|
||||
# only used for heap (malloc()).
|
||||
#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
|
||||
|
||||
EXTMEMOPTS =
|
||||
|
||||
|
||||
|
||||
#---------------- Linker Options ----------------
|
||||
# -Wl,...: tell GCC to pass this to linker.
|
||||
# -Map: create map file
|
||||
# --cref: add cross reference to map file
|
||||
LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
|
||||
LDFLAGS += -Wl,--relax
|
||||
LDFLAGS += -Wl,--gc-sections
|
||||
LDFLAGS += $(EXTMEMOPTS)
|
||||
LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
|
||||
LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
|
||||
#LDFLAGS += -T linker_script.x
|
||||
|
||||
|
||||
|
||||
#---------------- Programming Options (avrdude) ----------------
|
||||
|
||||
# Programming hardware
|
||||
# Type: avrdude -c ?
|
||||
# to get a full listing.
|
||||
#
|
||||
AVRDUDE_PROGRAMMER = jtagmkII
|
||||
|
||||
# com1 = serial port. Use lpt1 to connect to parallel port.
|
||||
AVRDUDE_PORT = usb
|
||||
|
||||
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
|
||||
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
|
||||
|
||||
|
||||
# Uncomment the following if you want avrdude's erase cycle counter.
|
||||
# Note that this counter needs to be initialized first using -Yn,
|
||||
# see avrdude manual.
|
||||
#AVRDUDE_ERASE_COUNTER = -y
|
||||
|
||||
# Uncomment the following if you do /not/ wish a verification to be
|
||||
# performed after programming the device.
|
||||
#AVRDUDE_NO_VERIFY = -V
|
||||
|
||||
# Increase verbosity level. Please use this when submitting bug
|
||||
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
|
||||
# to submit bug reports.
|
||||
#AVRDUDE_VERBOSE = -v -v
|
||||
|
||||
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
|
||||
|
||||
|
||||
|
||||
#---------------- Debugging Options ----------------
|
||||
|
||||
# For simulavr only - target MCU frequency.
|
||||
DEBUG_MFREQ = $(F_CPU)
|
||||
|
||||
# Set the DEBUG_UI to either gdb or insight.
|
||||
# DEBUG_UI = gdb
|
||||
DEBUG_UI = insight
|
||||
|
||||
# Set the debugging back-end to either avarice, simulavr.
|
||||
DEBUG_BACKEND = avarice
|
||||
#DEBUG_BACKEND = simulavr
|
||||
|
||||
# GDB Init Filename.
|
||||
GDBINIT_FILE = __avr_gdbinit
|
||||
|
||||
# When using avarice settings for the JTAG
|
||||
JTAG_DEV = /dev/com1
|
||||
|
||||
# Debugging port used to communicate between GDB / avarice / simulavr.
|
||||
DEBUG_PORT = 4242
|
||||
|
||||
# Debugging host used to communicate between GDB / avarice / simulavr, normally
|
||||
# just set to localhost unless doing some sort of crazy debugging when
|
||||
# avarice is running on a different computer.
|
||||
DEBUG_HOST = localhost
|
||||
|
||||
|
||||
|
||||
#============================================================================
|
||||
|
||||
|
||||
# Define programs and commands.
|
||||
SHELL = sh
|
||||
CC = avr-gcc
|
||||
OBJCOPY = avr-objcopy
|
||||
OBJDUMP = avr-objdump
|
||||
SIZE = avr-size
|
||||
AR = avr-ar rcs
|
||||
NM = avr-nm
|
||||
AVRDUDE = avrdude
|
||||
REMOVE = rm -f
|
||||
REMOVEDIR = rm -rf
|
||||
COPY = cp
|
||||
WINSHELL = cmd
|
||||
|
||||
|
||||
# Define Messages
|
||||
# English
|
||||
MSG_ERRORS_NONE = Errors: none
|
||||
MSG_BEGIN = -------- begin --------
|
||||
MSG_END = -------- end --------
|
||||
MSG_SIZE_BEFORE = Size before:
|
||||
MSG_SIZE_AFTER = Size after:
|
||||
MSG_COFF = Converting to AVR COFF:
|
||||
MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
|
||||
MSG_FLASH = Creating load file for Flash:
|
||||
MSG_EEPROM = Creating load file for EEPROM:
|
||||
MSG_EXTENDED_LISTING = Creating Extended Listing:
|
||||
MSG_SYMBOL_TABLE = Creating Symbol Table:
|
||||
MSG_LINKING = Linking:
|
||||
MSG_COMPILING = Compiling C:
|
||||
MSG_COMPILING_CPP = Compiling C++:
|
||||
MSG_ASSEMBLING = Assembling:
|
||||
MSG_CLEANING = Cleaning project:
|
||||
MSG_CREATING_LIBRARY = Creating library:
|
||||
|
||||
|
||||
|
||||
|
||||
# Define all object files.
|
||||
OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
|
||||
|
||||
# Define all listing files.
|
||||
LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
|
||||
|
||||
|
||||
# Compiler flags to generate dependency files.
|
||||
GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
|
||||
|
||||
|
||||
# Combine all necessary flags and optional flags.
|
||||
# Add target processor to flags.
|
||||
ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
|
||||
ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
|
||||
ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
# Default target.
|
||||
all: begin gccversion sizebefore build sizeafter end
|
||||
|
||||
# Change the build target to build a HEX file or a library.
|
||||
build: elf hex eep lss sym
|
||||
#build: lib
|
||||
|
||||
|
||||
elf: $(TARGET).elf
|
||||
hex: $(TARGET).hex
|
||||
eep: $(TARGET).eep
|
||||
lss: $(TARGET).lss
|
||||
sym: $(TARGET).sym
|
||||
LIBNAME=lib$(TARGET).a
|
||||
lib: $(LIBNAME)
|
||||
|
||||
|
||||
|
||||
# Eye candy.
|
||||
# AVR Studio 3.x does not check make's exit code but relies on
|
||||
# the following magic strings to be generated by the compile job.
|
||||
begin:
|
||||
@echo
|
||||
@echo $(MSG_BEGIN)
|
||||
|
||||
end:
|
||||
@echo $(MSG_END)
|
||||
@echo
|
||||
|
||||
|
||||
# Display size of file.
|
||||
HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
|
||||
ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
|
||||
MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
|
||||
FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
|
||||
|
||||
|
||||
sizebefore:
|
||||
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
|
||||
2>/dev/null; echo; fi
|
||||
|
||||
sizeafter:
|
||||
@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
|
||||
2>/dev/null; echo; fi
|
||||
|
||||
|
||||
|
||||
# Display compiler version information.
|
||||
gccversion :
|
||||
@$(CC) --version
|
||||
|
||||
|
||||
# Program the device.
|
||||
program: $(TARGET).hex $(TARGET).eep
|
||||
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
|
||||
|
||||
flip: $(TARGET).hex
|
||||
batchisp -hardware usb -device $(MCU) -operation erase f
|
||||
batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
|
||||
batchisp -hardware usb -device $(MCU) -operation start reset 0
|
||||
|
||||
dfu: $(TARGET).hex
|
||||
dfu-programmer $(MCU) erase
|
||||
dfu-programmer $(MCU) flash $(TARGET).hex
|
||||
dfu-programmer $(MCU) reset
|
||||
|
||||
flip-ee: $(TARGET).hex $(TARGET).eep
|
||||
$(COPY) $(TARGET).eep $(TARGET)eep.hex
|
||||
batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
|
||||
batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
|
||||
batchisp -hardware usb -device $(MCU) -operation start reset 0
|
||||
$(REMOVE) $(TARGET)eep.hex
|
||||
|
||||
dfu-ee: $(TARGET).hex $(TARGET).eep
|
||||
dfu-programmer $(MCU) eeprom-flash $(TARGET).eep
|
||||
dfu-programmer $(MCU) reset
|
||||
|
||||
|
||||
# Generate avr-gdb config/init file which does the following:
|
||||
# define the reset signal, load the target file, connect to target, and set
|
||||
# a breakpoint at main().
|
||||
gdb-config:
|
||||
@$(REMOVE) $(GDBINIT_FILE)
|
||||
@echo define reset >> $(GDBINIT_FILE)
|
||||
@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
|
||||
@echo end >> $(GDBINIT_FILE)
|
||||
@echo file $(TARGET).elf >> $(GDBINIT_FILE)
|
||||
@echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE)
|
||||
ifeq ($(DEBUG_BACKEND),simulavr)
|
||||
@echo load >> $(GDBINIT_FILE)
|
||||
endif
|
||||
@echo break main >> $(GDBINIT_FILE)
|
||||
|
||||
debug: gdb-config $(TARGET).elf
|
||||
ifeq ($(DEBUG_BACKEND), avarice)
|
||||
@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
|
||||
@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
|
||||
$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
|
||||
@$(WINSHELL) /c pause
|
||||
|
||||
else
|
||||
@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
|
||||
$(DEBUG_MFREQ) --port $(DEBUG_PORT)
|
||||
endif
|
||||
@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
|
||||
|
||||
|
||||
|
||||
|
||||
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
|
||||
COFFCONVERT = $(OBJCOPY) --debugging
|
||||
COFFCONVERT += --change-section-address .data-0x800000
|
||||
COFFCONVERT += --change-section-address .bss-0x800000
|
||||
COFFCONVERT += --change-section-address .noinit-0x800000
|
||||
COFFCONVERT += --change-section-address .eeprom-0x810000
|
||||
|
||||
|
||||
|
||||
coff: $(TARGET).elf
|
||||
@echo
|
||||
@echo $(MSG_COFF) $(TARGET).cof
|
||||
$(COFFCONVERT) -O coff-avr $< $(TARGET).cof
|
||||
|
||||
|
||||
extcoff: $(TARGET).elf
|
||||
@echo
|
||||
@echo $(MSG_EXTENDED_COFF) $(TARGET).cof
|
||||
$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
|
||||
|
||||
|
||||
|
||||
# Create final output files (.hex, .eep) from ELF output file.
|
||||
%.hex: %.elf
|
||||
@echo
|
||||
@echo $(MSG_FLASH) $@
|
||||
$(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock $< $@
|
||||
|
||||
%.eep: %.elf
|
||||
@echo
|
||||
@echo $(MSG_EEPROM) $@
|
||||
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
|
||||
--change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
|
||||
|
||||
# Create extended listing file from ELF output file.
|
||||
%.lss: %.elf
|
||||
@echo
|
||||
@echo $(MSG_EXTENDED_LISTING) $@
|
||||
$(OBJDUMP) -h -S -z $< > $@
|
||||
|
||||
# Create a symbol table from ELF output file.
|
||||
%.sym: %.elf
|
||||
@echo
|
||||
@echo $(MSG_SYMBOL_TABLE) $@
|
||||
$(NM) -n $< > $@
|
||||
|
||||
|
||||
|
||||
# Create library from object files.
|
||||
.SECONDARY : $(TARGET).a
|
||||
.PRECIOUS : $(OBJ)
|
||||
%.a: $(OBJ)
|
||||
@echo
|
||||
@echo $(MSG_CREATING_LIBRARY) $@
|
||||
$(AR) $@ $(OBJ)
|
||||
|
||||
|
||||
# Link: create ELF output file from object files.
|
||||
.SECONDARY : $(TARGET).elf
|
||||
.PRECIOUS : $(OBJ)
|
||||
%.elf: $(OBJ)
|
||||
@echo
|
||||
@echo $(MSG_LINKING) $@
|
||||
$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
|
||||
|
||||
|
||||
# Compile: create object files from C source files.
|
||||
$(OBJDIR)/%.o : %.c
|
||||
@echo
|
||||
@echo $(MSG_COMPILING) $<
|
||||
$(CC) -c $(ALL_CFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Compile: create object files from C++ source files.
|
||||
$(OBJDIR)/%.o : %.cpp
|
||||
@echo
|
||||
@echo $(MSG_COMPILING_CPP) $<
|
||||
$(CC) -c $(ALL_CPPFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Compile: create assembler files from C source files.
|
||||
%.s : %.c
|
||||
$(CC) -S $(ALL_CFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Compile: create assembler files from C++ source files.
|
||||
%.s : %.cpp
|
||||
$(CC) -S $(ALL_CPPFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Assemble: create object files from assembler source files.
|
||||
$(OBJDIR)/%.o : %.S
|
||||
@echo
|
||||
@echo $(MSG_ASSEMBLING) $<
|
||||
$(CC) -c $(ALL_ASFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Create preprocessed source for use in sending a bug report.
|
||||
%.i : %.c
|
||||
$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
|
||||
|
||||
|
||||
# Target: clean project.
|
||||
clean: begin clean_list end
|
||||
|
||||
clean_list :
|
||||
@echo
|
||||
@echo $(MSG_CLEANING)
|
||||
$(REMOVE) $(TARGET).hex
|
||||
$(REMOVE) $(TARGET).eep
|
||||
$(REMOVE) $(TARGET).cof
|
||||
$(REMOVE) $(TARGET).elf
|
||||
$(REMOVE) $(TARGET).map
|
||||
$(REMOVE) $(TARGET).sym
|
||||
$(REMOVE) $(TARGET).lss
|
||||
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
|
||||
$(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
|
||||
$(REMOVE) $(SRC:.c=.s)
|
||||
$(REMOVE) $(SRC:.c=.d)
|
||||
$(REMOVE) $(SRC:.c=.i)
|
||||
$(REMOVEDIR) .dep
|
||||
|
||||
doxygen:
|
||||
@echo Generating Project Documentation...
|
||||
@doxygen Doxygen.conf
|
||||
@echo Documentation Generation Complete.
|
||||
|
||||
clean_doxygen:
|
||||
rm -rf Documentation
|
||||
|
||||
# Create object files directory
|
||||
$(shell mkdir $(OBJDIR) 2>/dev/null)
|
||||
|
||||
|
||||
# Include the dependency files.
|
||||
-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
|
||||
|
||||
|
||||
# Listing of phony targets.
|
||||
.PHONY : all begin finish end sizebefore sizeafter gccversion \
|
||||
build elf hex eep lss sym coff extcoff doxygen clean \
|
||||
clean_list clean_doxygen program dfu flip flip-ee dfu-ee \
|
||||
debug gdb-config
|
||||
|
||||
|
|
@ -68,6 +68,8 @@ void SetupHardware(void)
|
|||
/* Hardware Initialization */
|
||||
Serial_Init(9600, false);
|
||||
Buttons_Init();
|
||||
ADC_Init(ADC_FREE_RUNNING | ADC_PRESCALE_32);
|
||||
ADC_SetupChannel(MIC_IN_ADC_CHANNEL);
|
||||
LEDs_Init();
|
||||
USB_Init();
|
||||
|
||||
|
|
@ -234,17 +236,30 @@ ISR(TIMER0_COMPA_vect, ISR_BLOCK)
|
|||
/* Check if the current pipe can be written to (device ready for more data) */
|
||||
if (Pipe_IsOUTReady())
|
||||
{
|
||||
static uint8_t SquareWaveSampleCount;
|
||||
static int16_t CurrentWaveValue;
|
||||
int16_t AudioSample;
|
||||
|
||||
#if defined(USE_TEST_TONE)
|
||||
static uint8_t SquareWaveSampleCount;
|
||||
static int16_t CurrentWaveValue;
|
||||
|
||||
if (SquareWaveSampleCount++ == 0xFF)
|
||||
CurrentWaveValue ^= 0x8000;
|
||||
/* In test tone mode, generate a square wave at 1/256 of the sample rate */
|
||||
if (SquareWaveSampleCount++ == 0xFF)
|
||||
CurrentWaveValue ^= 0x8000;
|
||||
|
||||
/* Only generate audio if the board button is being pressed */
|
||||
int16_t Sample_16Bit = (Buttons_GetStatus() & BUTTONS_BUTTON1) ? CurrentWaveValue : 0;
|
||||
/* Only generate audio if the board button is being pressed */
|
||||
AudioSample = (Buttons_GetStatus() & BUTTONS_BUTTON1) ? CurrentWaveValue : 0;
|
||||
#else
|
||||
/* Audio sample is ADC value scaled to fit the entire range */
|
||||
AudioSample = ((SAMPLE_MAX_RANGE / ADC_MAX_RANGE) * ADC_GetResult());
|
||||
|
||||
#if defined(MICROPHONE_BIASED_TO_HALF_RAIL)
|
||||
/* Microphone is biased to half rail voltage, subtract the bias from the sample value */
|
||||
AudioSample -= (SAMPLE_MAX_RANGE / 2);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
Pipe_Write_16_LE(Sample_16Bit);
|
||||
Pipe_Write_16_LE(Sample_16Bit);
|
||||
Pipe_Write_16_LE(AudioSample);
|
||||
Pipe_Write_16_LE(AudioSample);
|
||||
|
||||
if (!(Pipe_IsReadWriteAllowed()))
|
||||
Pipe_ClearOUT();
|
||||
|
|
|
|||
|
|
@ -48,12 +48,25 @@
|
|||
#include <LUFA/Drivers/Misc/TerminalCodes.h>
|
||||
#include <LUFA/Drivers/USB/USB.h>
|
||||
#include <LUFA/Drivers/Peripheral/Serial.h>
|
||||
#include <LUFA/Drivers/Peripheral/ADC.h>
|
||||
#include <LUFA/Drivers/Board/LEDs.h>
|
||||
#include <LUFA/Drivers/Board/Buttons.h>
|
||||
|
||||
#include "ConfigDescriptor.h"
|
||||
|
||||
/* Macros: */
|
||||
/** ADC channel number for the microphone input. */
|
||||
#define MIC_IN_ADC_CHANNEL 2
|
||||
|
||||
/** ADC channel MUX mask for the microphone input. */
|
||||
#define MIC_IN_ADC_MUX_MASK ADC_CHANNEL2
|
||||
|
||||
/** Maximum audio sample value for the microphone input. */
|
||||
#define SAMPLE_MAX_RANGE 0xFFFF
|
||||
|
||||
/** Maximum ADC range for the microphone input. */
|
||||
#define ADC_MAX_RANGE 0x3FF
|
||||
|
||||
/** LED mask for the library LED driver, to indicate that the USB interface is not ready. */
|
||||
#define LEDMASK_USB_NOTREADY LEDS_LED1
|
||||
|
||||
|
|
|
|||
File diff suppressed because one or more lines are too long
|
|
@ -209,7 +209,7 @@ uint8_t Audio_GetSetEndpointProperty(USB_ClassInfo_Audio_Host_t* const AudioInte
|
|||
const uint8_t EndpointProperty,
|
||||
const uint8_t EndpointControl,
|
||||
uint16_t const DataLength,
|
||||
uint8_t* Data)
|
||||
void* const Data)
|
||||
{
|
||||
uint8_t RequestType;
|
||||
uint8_t EndpointAddress;
|
||||
|
|
|
|||
|
|
@ -159,8 +159,8 @@
|
|||
const uint8_t DataPipeIndex,
|
||||
const uint8_t EndpointProperty,
|
||||
const uint8_t EndpointControl,
|
||||
uint16_t* const DataLength,
|
||||
uint8_t* Data);
|
||||
uint16_t const DataLength,
|
||||
void* const Data);
|
||||
|
||||
/* Inline Functions: */
|
||||
/** General management task for a given Audio host class interface, required for the correct operation of
|
||||
|
|
@ -192,8 +192,13 @@
|
|||
if ((USB_HostState != HOST_STATE_Configured) || !(AudioInterfaceInfo->State.IsActive))
|
||||
return false;
|
||||
|
||||
bool SampleReceived = false;
|
||||
|
||||
Pipe_SelectPipe(AudioInterfaceInfo->Config.DataOUTPipeNumber);
|
||||
return Pipe_IsINReceived();
|
||||
Pipe_Unfreeze();
|
||||
SampleReceived = Pipe_IsINReceived();
|
||||
Pipe_Freeze();
|
||||
return SampleReceived;
|
||||
}
|
||||
|
||||
/** Determines if the given audio interface is ready to accept the next sample to be written to it, and selects
|
||||
|
|
@ -237,7 +242,11 @@
|
|||
Sample = Pipe_Read_8();
|
||||
|
||||
if (!(Pipe_BytesInPipe()))
|
||||
Pipe_ClearIN();
|
||||
{
|
||||
Pipe_Unfreeze();
|
||||
Pipe_ClearIN();
|
||||
Pipe_Freeze();
|
||||
}
|
||||
|
||||
return Sample;
|
||||
}
|
||||
|
|
@ -262,7 +271,11 @@
|
|||
Sample = (int16_t)Pipe_Read_16_LE();
|
||||
|
||||
if (!(Pipe_BytesInPipe()))
|
||||
Pipe_ClearIN();
|
||||
{
|
||||
Pipe_Unfreeze();
|
||||
Pipe_ClearIN();
|
||||
Pipe_Freeze();
|
||||
}
|
||||
|
||||
return Sample;
|
||||
}
|
||||
|
|
@ -287,7 +300,11 @@
|
|||
Sample = (((uint32_t)Pipe_Read_8() << 16) | Pipe_Read_16_LE());
|
||||
|
||||
if (!(Pipe_BytesInPipe()))
|
||||
Pipe_ClearIN();
|
||||
{
|
||||
Pipe_Unfreeze();
|
||||
Pipe_ClearIN();
|
||||
Pipe_Freeze();
|
||||
}
|
||||
|
||||
return Sample;
|
||||
}
|
||||
|
|
@ -308,7 +325,11 @@
|
|||
Pipe_Write_8(Sample);
|
||||
|
||||
if (Pipe_BytesInPipe() == AudioInterfaceInfo->State.DataINPipeSize)
|
||||
Pipe_ClearOUT();
|
||||
{
|
||||
Pipe_Unfreeze();
|
||||
Pipe_ClearOUT();
|
||||
Pipe_Freeze();
|
||||
}
|
||||
}
|
||||
|
||||
/** Writes the next 16-bit audio sample to the current audio interface.
|
||||
|
|
@ -327,7 +348,11 @@
|
|||
Pipe_Write_16_LE(Sample);
|
||||
|
||||
if (Pipe_BytesInPipe() == AudioInterfaceInfo->State.DataINPipeSize)
|
||||
Pipe_ClearOUT();
|
||||
{
|
||||
Pipe_Unfreeze();
|
||||
Pipe_ClearOUT();
|
||||
Pipe_Freeze();
|
||||
}
|
||||
}
|
||||
|
||||
/** Writes the next 24-bit audio sample to the current audio interface.
|
||||
|
|
@ -347,7 +372,11 @@
|
|||
Pipe_Write_8(Sample >> 16);
|
||||
|
||||
if (Pipe_BytesInPipe() == AudioInterfaceInfo->State.DataINPipeSize)
|
||||
Pipe_ClearOUT();
|
||||
{
|
||||
Pipe_Unfreeze();
|
||||
Pipe_ClearOUT();
|
||||
Pipe_Freeze();
|
||||
}
|
||||
}
|
||||
|
||||
/* Private Interface - For use in library only: */
|
||||
|
|
|
|||
|
|
@ -66,6 +66,8 @@
|
|||
* Measurement class
|
||||
* - <b>Host</b>
|
||||
* - <b>ClassDriver</b>
|
||||
* - <b>AudioInputHost</b> - Audio Input host demo, using the library USB Audio Class driver framework
|
||||
* - <b>AudioOutputHost</b> - Audio Output host demo, using the library USB Audio Class driver framework
|
||||
* - <b>JoystickHostWithParser</b> - Joystick host demo with HID Descriptor parser, using the library USB HID Class driver framework
|
||||
* - <b>KeyboardHost</b> - USB Keyboard host demo, using the library USB HID Class driver framework
|
||||
* - <b>KeyboardHostWithParser</b> - USB Keyboard host demo with HID Descriptor parser, using the library USB HID Class
|
||||
|
|
@ -77,8 +79,8 @@
|
|||
* - <b>StillImageHost</b> - Still Image Camera host demo, using the library USB Still Image Class driver framework
|
||||
* - <b>VirtualSerialHost</b> - Virtual Serial Port host demo, using the library USB CDC Class driver framework
|
||||
* - <b>LowLevel</b>
|
||||
* - <b>AudioInputHost</b> - Incomplete Audio Input host demo, using the low level LUFA APIs to implement a USB microphone host
|
||||
* - <b>AudioOutputHost</b> - Incomplete Audio Output host demo, using the low level LUFA APIs to implement a USB speaker host
|
||||
* - <b>AudioInputHost</b> - Audio Input host demo, using the low level LUFA APIs to implement the USB Audio class
|
||||
* - <b>AudioOutputHost</b> - Audio Output host demo, using the low level LUFA APIs to implement the USB Audio class
|
||||
* - <b>GenericHIDHost</b> - Generic HID host demo, using the low level LUFA APIs to implement the USB HID class
|
||||
* - <b>JoystickHostWithParser</b> - Joystick host demo with HID Descriptor parser, using the low level LUFA APIs to implement
|
||||
* the USB HID class
|
||||
|
|
|
|||
Loading…
Reference in New Issue