Add top level documentation to the Mass Storage class bootloader.

Bootloaders/Incomplete/MassStorage/BootloaderMassStorage.txt

@@ -0,0 +1,159 @@
+/** \file
+ *
+ *  This file contains special DoxyGen information for the generation of the main page and other special
+ *  documentation pages. It is not a project source file.
+ */
+
+/** \mainpage Mass Storage Class USB AVR Bootloader
+ *
+ *  \section Sec_Compat Demo Compatibility:
+ *
+ *  The following list indicates what microcontrollers are compatible with this demo.
+ *
+ *  \li Series 7 USB AVRs (AT90USBxxx7)
+ *  \li Series 6 USB AVRs (AT90USBxxx6)
+ *
+ *  \section Sec_Info USB Information:
+ *
+ *  The following table gives a rundown of the USB utilization of this demo.
+ *
+ *  <table>
+ *   <tr>
+ *    <td><b>USB Mode:</b></td>
+ *    <td>Device</td>
+ *   </tr>
+ *   <tr>
+ *    <td><b>USB Class:</b></td>
+ *    <td>Mass Storage Device</td>
+ *   </tr>
+ *   <tr>
+ *    <td><b>USB Subclass:</b></td>
+ *    <td>Bulk-Only Transport</td>
+ *   </tr>
+ *   <tr>
+ *    <td><b>Relevant Standards:</b></td>
+ *    <td>USBIF Mass Storage Standard \n
+ *        USB Bulk-Only Transport Standard \n
+ *        SCSI Primary Commands Specification \n
+ *        SCSI Block Commands Specification</td>
+ *   </tr>
+ *   <tr>
+ *    <td><b>Supported USB Speeds:</b></td>
+ *    <td>Full Speed Mode</td>
+ *   </tr>
+ *  </table>
+ *
+ *  \section Sec_Description Project Description:
+ *
+ *  This bootloader enumerates to the host as a Mass Storage device, capable of reading and writing a new binary
+ *  firmware image file, to load firmware onto the AVR.
+ *
+ *  Out of the box this bootloader builds for the AT90USB1287 with an 8KB bootloader section size, and will fit
+ *  into 8KB of bootloader space. If you wish to alter this size and/or change the AVR model, you will need to
+ *  edit the MCU, FLASH_SIZE_KB and BOOT_SECTION_SIZE_KB values in the accompanying makefile.
+ *
+ *  When the bootloader is running, the board's LED(s) will flash at regular intervals to distinguish the
+ *  bootloader from the normal user application.
+ *
+ *  \section Sec_Installation Driver Installation
+ *
+ *  This bootloader uses the Mass Storage printer drivers inbuilt into all modern operating systems, thus no additional
+ *  drivers need to be supplied for correct operation.
+ *
+ *  \section Sec_HostApp Host Controller Application
+ *
+ *  This bootloader is compatible with all operating systems that support the FAT12 file system format. To reprogram the
+ *  device, overwrite a file stored on the virtual FAT filesystem with a new binary (BIN format) image. Remember to safely
+ *  remove your device from the host using the host OS's ejection APIs, to ensure all data is correctly flushed to the
+ *  bootloader's virtual filesystem and not cached in the OS's file system driver.
+ *
+ *  The current device firmware can be read from the device by reading a file from the virtual FAT filesystem.
+ *
+ *  \section Sec_API User Application API
+ *
+ *  Several user application functions for FLASH and other special memory area manipulations are exposed by the bootloader,
+ *  allowing the user application to call into the bootloader at runtime to read and write FLASH data.
+ *
+ *  By default, the bootloader API jump table is located 32 bytes from the end of the device's FLASH memory, and follows the
+ *  following layout:
+ *
+ *  \code
+ *  #define BOOTLOADER_API_TABLE_SIZE          32
+ *  #define BOOTLOADER_API_TABLE_START         ((FLASHEND + 1UL) - BOOTLOADER_API_TABLE_SIZE)
+ *  #define BOOTLOADER_API_CALL(Index)         (void*)((BOOTLOADER_API_TABLE_START + (Index * 2)) / 2)
+ *
+ *  void    (*BootloaderAPI_ErasePage)(uint32_t Address)               = BOOTLOADER_API_CALL(0);
+ *  void    (*BootloaderAPI_WritePage)(uint32_t Address)               = BOOTLOADER_API_CALL(1);
+ *  void    (*BootloaderAPI_FillWord)(uint32_t Address, uint16_t Word) = BOOTLOADER_API_CALL(2);
+ *  uint8_t (*BootloaderAPI_ReadSignature)(uint16_t Address)           = BOOTLOADER_API_CALL(3);
+ *  uint8_t (*BootloaderAPI_ReadFuse)(uint16_t Address)                = BOOTLOADER_API_CALL(4);
+ *  uint8_t (*BootloaderAPI_ReadLock)(void)                            = BOOTLOADER_API_CALL(5);
+ *  void    (*BootloaderAPI_WriteLock)(uint8_t LockBits)               = BOOTLOADER_API_CALL(6);
+ *
+ *  #define BOOTLOADER_MAGIC_SIGNATURE_START   (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 2))
+ *  #define BOOTLOADER_MAGIC_SIGNATURE         0xDCFB
+ *
+ *  #define BOOTLOADER_CLASS_SIGNATURE_START   (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 4))
+ *  #define BOOTLOADER_MASS_STORAGE_SIGNATURE  0xDF30
+ *
+ *  #define BOOTLOADER_ADDRESS_START           (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 8))
+ *  #define BOOTLOADER_ADDRESS_LENGTH          4
+ *  \endcode
+ *
+ *  \subsection SSec_API_MemLayout Device Memory Map
+ *  The following illustration indicates the final memory map of the device when loaded with the bootloader.
+ *
+ *  \verbatim
+ *  +----------------------------+ 0x0000
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |      User Application      |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  |                            |
+ *  +----------------------------+ FLASHEND - BOOT_SECTION_SIZE
+ *  |                            |
+ *  |   Bootloader Application   |
+ *  | (Not User App. Accessible) |
+ *  |                            |
+ *  +----------------------------+ FLASHEND - 96
+ *  |   API Table Trampolines    |
+ *  | (Not User App. Accessible) |
+ *  +----------------------------+ FLASHEND - 32
+ *  |    Bootloader API Table    |
+ *  |   (User App. Accessible)   |
+ *  +----------------------------+ FLASHEND - 8
+ *  |   Bootloader ID Constants  |
+ *  |   (User App. Accessible)   |
+ *  +----------------------------+ FLASHEND
+ *  \endverbatim
+ *
+ *  Bootloaders reporting a device release revision number of 1.00 or greater are bootloader API enabled. From the application
+ *  the API support of the bootloader can be detected by reading the FLASH memory bytes located at address \c BOOTLOADER_MAGIC_SIGNATURE_START
+ *  and comparing them to the value \c BOOTLOADER_MAGIC_SIGNATURE. The class of bootloader can be determined by reading the
+ *  FLASH memory bytes located at address \c BOOTLOADER_CLASS_SIGNATURE_START and comparing them to the value \c BOOTLOADER_MASS_STORAGE_SIGNATURE.
+ *  The start address of the bootloader can be retrieved by reading the bytes of FLASH memory starting from address \c BOOTLOADER_ADDRESS_START.
+ *
+ *  \section Sec_Options Project Options
+ *
+ *  The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
+ *
+ *  <table>
+ *   <tr>
+ *    <td>
+ *     None
+ *    </td>
+ *   </tr>
+ *  </table>
+ */
+