wip

drivers/arm/i2c_master.c

@@ -65,11 +65,12 @@ uint8_t i2c_start(uint8_t address)
   return 0;
 }
 
-uint8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)
+int8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)
 {
   i2c_address = address;
   i2cStart(&I2C_DRIVER, &i2cconfig);
-  return i2cMasterTransmitTimeout(&I2C_DRIVER, (i2c_address >> 1), data, length, 0, 0, MS2ST(timeout));
+  int8_t result = i2cMasterTransmitTimeout(&I2C_DRIVER, (i2c_address >> 1), data, length, 0, 0, MS2ST(timeout));
+  return result;
 }
 
 uint8_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)

drivers/arm/i2c_master.h

@@ -42,7 +42,7 @@
 
 void i2c_init(void);
 uint8_t i2c_start(uint8_t address);
-uint8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);
+int8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);
 uint8_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);
 uint8_t i2c_transmit_receive(uint8_t address, uint8_t * tx_body, uint16_t tx_length, uint8_t * rx_body, uint16_t rx_length);
 uint8_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout);

drivers/issi/is31fl3235a.c

@@ -42,7 +42,7 @@
 #define ISSI_BANK_FUNCTIONREG 0x0B    // FIXME: Not on 3235?
 
 #ifndef ISSI_TIMEOUT
-  #define ISSI_TIMEOUT 100
+  #define ISSI_TIMEOUT 255
 #endif
 
 #ifndef ISSI_PERSISTENCE
@@ -73,9 +73,9 @@ bool g_rgb7seg_buffer_update_required = false;
 bool g_rgb7seg_control_registers_update_required = false;
 
 void IS31FL3235A_write_register(uint8_t addr, uint8_t reg, uint8_t data) {
-    xprintf("IS31FL3235A_write_register(0x%x, 0x%x, 0x%x);\n", addr, reg, data);
     g_3235a_transfer_buffer[0] = reg;
     g_3235a_transfer_buffer[1] = data;
+    xprintf("IS31FL3235A_write_register(0x%x, 0x%x, 0x%x); g_3235a_transfer_buffer:0x%x\n", addr, reg, data, g_3235a_transfer_buffer);
 
     #if ISSI_PERSISTENCE > 0
         for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
@@ -84,7 +84,13 @@ void IS31FL3235A_write_register(uint8_t addr, uint8_t reg, uint8_t data) {
             }
         }
     #else
-        i2c_transmit(addr << 1, g_3235a_transfer_buffer, 2, ISSI_TIMEOUT);
+        if (i2c_transmit(addr << 1, g_3235a_transfer_buffer, 2, ISSI_TIMEOUT) == -1) {
+            // When we encounter a timeout ChibiOS says the bus must be reset as it's in an unknown state
+            xprintf("i2c transmit timeout, resetting i2c bus!\n");
+            i2c_stop(ISSI_TIMEOUT);
+            wait_ms(5);
+            i2c_start(ISSI_TIMEOUT);
+        }
     #endif
 }
 
@@ -111,9 +117,13 @@ void IS31FL3235A_write_pwm_buffer(uint8_t addr, uint8_t *pwm_buffer) {
           break;
       }
     #else
-      if (!i2c_transmit(addr << 1, g_3235a_transfer_buffer, 17, ISSI_TIMEOUT)) {
+        if (i2c_transmit(addr << 1, g_3235a_transfer_buffer, 17, ISSI_TIMEOUT) == -1) {
-          xprintf("Could not contact i2c device 0x%x!\n", addr << 1);
+            // When we encounter a timeout ChibiOS says the bus must be reset as it's in an unknown state
-      }
+            xprintf("i2c transmit timeout, resetting i2c bus!\n");
+            i2c_stop(ISSI_TIMEOUT);
+            wait_ms(5);
+            i2c_start(ISSI_TIMEOUT);
+        }
     #endif
     }
 }
@@ -132,14 +142,37 @@ void IS31FL3235A_init(uint8_t addr) {
     // this delay was copied from other drivers, might not be needed
     wait_ms(10);
 
+    // This is how the Arduino code does init...
+    uint8_t i = 0;
+
+    for (i=0x2A; i<=0x45; i++) {
+        IS31FL3235A_write_register(addr, i, 0xFF);  // Turn off all LEDs
+    }
+
+    for (i=0x05; i<=0x20; i++) {
+        IS31FL3235A_write_register(addr, i, 0x00);  // Write all PWM set 0x00
+    }
+
+    IS31FL3235A_write_register(addr, 0x25, 0x00);   //update PWM&Control registers
+    IS31FL3235A_write_register(addr, 0x4B, 0x01);   //frequency setting 22KHz
+    IS31FL3235A_write_register(addr, 0x00, 0x01);   //normal operation
+
+    // This is how the Arduino code does LED turn on
+    IS31FL3235A_write_register(addr, 0x05, 0xFF);   // set PWM
+    IS31FL3235A_write_register(addr, 0x25, 0x00);   // update PWM&Control registers
+    IS31FL3235A_write_register(addr, 0x08, 0xFF);   // set PWM
+    IS31FL3235A_write_register(addr, 0x25, 0x00);   // update PWM&Control registers
+    IS31FL3235A_write_register(addr, 0x12, 0xFF);   // set PWM
+    IS31FL3235A_write_register(addr, 0x25, 0x00);   // update PWM&Control registers
+
     // FIXME: This is for testing, turn on OUT1 at full brightness
-    IS31FL3235A_write_register(addr, 0x2A, 0xFF);
+    //IS31FL3235A_write_register(addr, 0x2A, 0xFF);
-    IS31FL3235A_write_register(addr, 0x05, 0x00);
+    //IS31FL3235A_write_register(addr, 0x05, 0x00);
 
     // I think this finally turns it on?
-    IS31FL3235A_write_register(addr, 0x25, 0x00);    //update PWM&Control registers
+    //IS31FL3235A_write_register(addr, 0x25, 0x00);    //update PWM&Control registers
     //IS31FL3235A_write_register(addr, 0x4B, 0x01);  //frequency setting 22KHz
-    IS31FL3235A_write_register(addr, 0x00, 0x01);    //normal operation
+    //IS31FL3235A_write_register(addr, 0x00, 0x01);    //normal operation
 }
 
 void IS31FL3235A_set_value(int index, uint8_t value) {

drivers/qwiic/rgb7seg.c

@@ -128,16 +128,14 @@ void rgb7seg_task(void) {
 }
 
 void rgb7seg_init(void) {
-    #ifdef IS31FL3235A_DRIVER_ADDR_1
+    IS31FL3235A_init(IS31FL3235A_DRIVER_ADDR_1);
-        IS31FL3235A_init(IS31FL3235A_DRIVER_ADDR_1);
+    #if IS31FL3235A_COUNT > 1
-    #endif
-    #ifdef IS31FL3235A_DRIVER_ADDR_2
         IS31FL3235A_init(IS31FL3235A_DRIVER_ADDR_2);
     #endif
-    #ifdef IS31FL3235A_DRIVER_ADDR_3
+    #if IS31FL3235A_COUNT > 2
         IS31FL3235A_init(IS31FL3235A_DRIVER_ADDR_3);
     #endif
-    #ifdef IS31FL3235A_DRIVER_ADDR_4
+    #if IS31FL3235A_COUNT > 3
         IS31FL3235A_init(IS31FL3235A_DRIVER_ADDR_4);
     #endif
 

keyboards/clueboard/60/config.h

@@ -47,7 +47,7 @@
  *
 */
 #define MATRIX_ROW_PINS { B0, B1, B2, A15, A10 }
-#define MATRIX_COL_PINS { A2, A3, A6, B14, B15, A8, A9, A7, B3, B4, C14, C15, C13, B5, B6 }
+#define MATRIX_COL_PINS { A2, A3, A6, B14, B15, A8, A9, A7, B3, B4, C15, C14, C13, B5, B6 }
 #define UNUSED_PINS { A0, A1, A9, B7, B8, B9, B10, B11, B12, B13 }
 #define DIODE_DIRECTION COL2ROW
 

keyboards/clueboard/66/rev4/config.h

@@ -37,6 +37,17 @@
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
+/* key combination for command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+#define IS31FL3235A_COUNT 1
+//#define I2C_DRIVER I2CD1
+#define I2C1_BANK GPIOB
+#define I2C1_SCL 8
+#define I2C1_SDA 9
+
 /*
  * Feature disable options
  *  These options are also useful to firmware size reduction.

keyboards/clueboard/66/rev4/halconf.h

@@ -76,7 +76,7 @@
  * @brief   Enables the I2C subsystem.
  */
 #if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
-#define HAL_USE_I2C                 FALSE
+#define HAL_USE_I2C                 TRUE
 #endif
 
 /**

keyboards/clueboard/66/rev4/mcuconf.h

@@ -154,7 +154,7 @@
 /*
  * I2C driver system settings.
  */
-#define STM32_I2C_USE_I2C1                  FALSE
+#define STM32_I2C_USE_I2C1                  TRUE
 #define STM32_I2C_USE_I2C2                  FALSE
 #define STM32_I2C_BUSY_TIMEOUT              50
 #define STM32_I2C_I2C1_IRQ_PRIORITY         10

keyboards/clueboard/66/rev4/rules.mk

@@ -17,6 +17,8 @@ DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave
 # Build Options
 #   comment out to disable the options.
 #
+QWIIC_ENABLE = RGB7SEG
+
 BACKLIGHT_ENABLE = yes
 BOOTMAGIC_ENABLE = no   # Virtual DIP switch configuration(+1000)
 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)

keyboards/clueboard/66_hotswap/gen1/config.h

@@ -131,7 +131,7 @@
 #define BACKLIGHT_LEVELS 10
 
 // For the rgb7seg
-#define IS31FL3235A_COUNT 4
+#define IS31FL3235A_COUNT 1
 #define I2C_DRIVER I2CD2
 #define I2C1_BANK GPIOA
 #define I2C1_SCL 9