mirror of
https://github.com/mfulz/qmk_firmware.git
synced 2025-10-31 05:12:33 +01:00
63 lines
2.9 KiB
C
63 lines
2.9 KiB
C
/*
|
|
Copyright 2022 Thomas Baart <thomas@splitkb.com>
|
|
|
|
This program is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 2 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#pragma once
|
|
|
|
// Side detection
|
|
// col 4 row 3 on right-hand-side
|
|
#define SPLIT_HAND_MATRIX_GRID E6, B3 // row first because the board is col2row
|
|
#define SPLIT_HAND_MATRIX_GRID_LOW_IS_RIGHT
|
|
#define MATRIX_MASKED // actual mask is defined by `matrix_mask` in `rev2.c`
|
|
|
|
/*
|
|
* Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
|
|
*/
|
|
|
|
#if defined(CONVERT_TO_PROTON_C)
|
|
# define SERIAL_USART_FULL_DUPLEX // Enable full duplex operation mode.
|
|
# define SERIAL_USART_PIN_SWAP // Swap TX and RX pins if keyboard is master halve.
|
|
# define SERIAL_USART_DRIVER SD1 // USART driver of TX pin. default: SD1
|
|
# define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
|
|
# define SERIAL_USART_TX_PIN D3
|
|
# define SERIAL_USART_RX_PIN D2
|
|
|
|
# define WS2812_DI_PIN PAL_LINE(GPIOA, 3)
|
|
# define WS2812_PWM_DRIVER PWMD2 // default: PWMD2
|
|
# define WS2812_PWM_CHANNEL 4 // default: 2
|
|
# define WS2812_PWM_PAL_MODE 1 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 2
|
|
# define WS2812_DMA_STREAM STM32_DMA1_STREAM2 // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
|
|
# define WS2812_DMA_CHANNEL 2 // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
|
|
# define WS2812_DMAMUX_ID STM32_DMAMUX1_TIM2_UP // DMAMUX configuration for TIMx_UP -- only required if your MCU has a DMAMUX peripheral, see the respective reference manual for the appropriate values for your MCU.
|
|
#else
|
|
# define WS2812_DI_PIN D3
|
|
# define SOFT_SERIAL_PIN D2
|
|
#endif
|
|
|
|
#ifdef OLED_ENABLE
|
|
# define OLED_DISPLAY_128X64
|
|
# define SPLIT_OLED_ENABLE
|
|
#endif
|
|
|
|
/* RGB matrix support */
|
|
#ifdef RGB_MATRIX_ENABLE
|
|
# define SPLIT_TRANSPORT_MIRROR
|
|
# define RGB_MATRIX_LED_COUNT 20 // Number of LEDs
|
|
# define RGB_MATRIX_SPLIT { 10, 10 }
|
|
# define RGB_MATRIX_MAXIMUM_BRIGHTNESS 170
|
|
# define RGB_DISABLE_WHEN_USB_SUSPENDED
|
|
#endif
|