a9f313afa9
Slow AVRISP-MKII clone PDI/TPI programming speed back to 250KHz due to issues with the XPLAINBridge when PDI programming at faster rates.
...
Speed up XMEGANVM_WaitWhileNVMControllerBusy() by preloading the status register address into the pointer register of the target's NVM controller and then reading via a faster indirect load command.
2010-11-16 12:30:00 +00:00
002cd6df49
Added new XCK_RESCUE_CLOCK_ENABLE compile time option to the AVRISP-MKII clone programmer project (thanks to Tom Light).
2010-11-16 01:37:43 +00:00
b27f35536d
Fixed incorrect event name in the Benito project.
2010-11-15 08:24:18 +00:00
f2324fc2b4
Second patch to fix incorrect PDI/TPI programming speed.
2010-11-14 06:44:57 +00:00
d41cd9a41a
Fixed PDI/TPI programming speed of ~250KHz in the AVRISP-MKII Clone project, instead of the desired 500KHz.
2010-11-12 06:24:01 +00:00
50390867e7
Fixed incorrect PollingIntervalMS values in the demo/project/bootloader endpoint descriptors (thanks to MCS Electronics).
2010-11-10 12:38:25 +00:00
0ce2950d81
Added board hardware driver support for the Adafruit U4 breakout board.
...
Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.
Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).
2010-11-08 03:41:48 +00:00
bac860b173
Fixed broken input in the MagStripe reader project due to an incorrect HID report descriptor.
2010-11-07 12:54:52 +00:00
fb76acb084
Renamed the EVENT_USB_Device_UnhandledControlRequest() event to EVENT_USB_Device_ControlRequest() as it is now fired before the library request handlers, not afterwards.
2010-11-05 05:15:20 +00:00
85cf202737
Fixed USBtoSerial and XPLAINBridge demos discarding data from the PC if the send buffer becomes full.
2010-11-03 11:24:34 +00:00
5ce8380a7d
Fix XPLAINBridge code broken during the changes to the Rescue Clock generation in the AVRISP-MKII clone project.
...
Change over all low level host mode project's descriptor comparator routines to perform the descriptor casting in a temp variable to make the code clearer and easier to modify (despite being more verbose).
2010-11-02 11:16:36 +00:00
3bf760ad7d
Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times when 125KHz ISP programming mode is selected.
2010-11-02 07:57:23 +00:00
cb779e3d7d
Changed over www.fourwalledcubicle.com links to the new www.lufa-lib.org redirect domain, including the new aliased links for LUFA-related pages such as the various download/source control mirrors and support lists.
2010-10-28 06:08:58 +00:00
55538dcef3
Add descriptor class, subclass and protocol constants to the class drivers, modify all demos to use them where possible.
...
Move out private/internal host class driver constants to the common class driver headers, so that they can be used in the Low Level host mode demos.
Ensure all demos, projects and bootloaders use the class driver constants where possible to minimise code repetition.
2010-10-25 12:42:55 +00:00
b37d77eab3
All USB class drivers are now automatically included when LUFA/Drivers/USB.h is included, and no longer need to be seperately included.
...
All LowLevel demos changed to use the constants and types defined in the USB class drivers.
2010-10-24 22:53:57 +00:00
421479a4b9
Fix incomplete StandaloneProgrammer project code not compiling due to the recent API changes in the LUFA core.
2010-10-13 14:25:36 +00:00
31daf04c6a
Fix SoftUART.c not compiling due to accidental check in of changes not yet complete in the rest of the XPLAINBridge project code.
2010-10-13 14:23:23 +00:00
3661ae8dfb
Minor documentation corrections.
2010-10-13 14:10:24 +00:00
5a4def7478
Clean up excessive whitespace at the end of each line using the wspurify tool made by Laszlo Monda
2010-10-13 14:05:35 +00:00
3693916cd3
Fix Webserver project code not compiling due to the changes to the USB mode selection constant names.
2010-10-12 12:25:05 +00:00
3a03da9705
Fixed ISR definition conflict in the XPLAIN bridge between the software UART and the AVRISP-MKII ISP modules.
2010-10-10 06:23:45 +00:00
93793679c9
Revert change to the AVRISP-MKII project for fuse byte programming via the CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.
2010-10-02 10:07:24 +00:00
a447ae134f
Fixed broken lock byte programming in the AVRISP-MKII clone project for some XMEGA targets.
2010-10-02 10:02:24 +00:00
824ce10390
Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used.
2010-10-02 08:41:08 +00:00
c8942ef469
Fixed LowLevel JoystickHostWithParser demo not saving the chosen HID interface's report descriptor size.
...
Simplified low level Host demo configuration descriptor parser routines.
2010-10-01 12:01:54 +00:00
7166c7ba3e
Fix low level host mode demos not correctly fetching the next endpoint when an invalid interface is discarded.
...
Update the pipe configuration routines in the host mode class drivers so that they use the same new code to enumerate compatible devices to increase reliability. Add support to the host mode class drivers for non-sequential (but non-overlapping with other interface) pipe numbers.
2010-09-30 07:56:47 +00:00
158afe9109
Reverted Endpoint/Pipe non-sequential configuration hack, placed restriction on the configuration order instead to ensure maximum reliability.
...
Altered all low level device and host mode demos to ensure that endpoints and pipes are configured in ascending order properly.
Rewrote all low level host mode demos' configuration descriptor parser code to ensure that pipes are enumerated in ascending order, and to ensure maximum compatibility with devices.
Incremented all device mode demo's device descriptor revision numbers to ensure that any descriptor changes are re-fetched on machines which have enumerated previous versions.
2010-09-30 06:23:38 +00:00
a509729b2d
Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive.
...
Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set.
2010-09-29 13:56:52 +00:00
713670043a
Move out many of the common class driver constants into grouped enums, to make them more managable.
...
Add new CDC descriptor structs to the CDC class driver, so that the CDC demos can use human readable field names.
Rename prefix for Still Image Host class driver functions from "SImage_" to "SI_" to remain consistent with the rest of the driver.
2010-09-28 12:14:06 +00:00
800485bd95
Remove dfu-programmer program switches, to ensure maximum compatibility with all dfu-programmer versions.
2010-09-24 06:59:28 +00:00
bd85422d2b
Added the --suppress-bootloader-mem option to the makefile dfu target, to ensure that writes to the bootloader section of the AVR's flash memory are ignored (thanks to Axel Rohde).
...
Fixed incorrect command name for EEPROM memory programming in the makefile dfu-ee target.
Makefile whitespace fixes.
2010-09-24 06:45:11 +00:00
6d2f091cec
Make project makefiles correctly clean intermeditary build files from assembly and C++ sources (thanks to Daniel Czigany).
2010-09-15 03:00:29 +00:00
84696c727d
Added board hardware driver support for the BUI development board.
2010-09-14 11:11:54 +00:00
def0e0ff1b
Remove incomplete MIDIToneGenerator project.
2010-09-13 10:07:45 +00:00
fdcb486e22
Fix typos in the project overview text files.
2010-09-09 13:39:52 +00:00
c166dfc64e
Added class specific descriptor type defines with standard USB-IF element naming.
2010-09-09 13:05:57 +00:00
4dece08bef
Clarify in the project documentation files what the each of the different USB AVR device "series" comprises of.
2010-08-31 12:33:21 +00:00
009eebf229
Fix incorrect ADC driver documentation for the parameters of ADC_Init(), fix incorrect call to ADC_Init() in the TemperatureDatalogger project.
2010-08-31 07:32:48 +00:00
b3c6599bb7
Remove remaining void* descriptor casts in the projects and demos that were not removed when the GetDescriptor callback function's signature was altered.
2010-08-29 13:21:14 +00:00
263178fbb6
Add better description of the Ultra-Lightweight Ring Buffer header files.
2010-08-29 07:49:36 +00:00
092f82e06f
Changed the signature of the CALLBACK_USB_GetDescriptor() callback function so that the descriptor pointer is const, to remove the need for extra casting inside the callback (thanks to Jonathan Kollasch).
2010-08-24 13:02:38 +00:00
1be3436e89
Moved calls to Device mode Class Driver events to after the request has been acknowledged, so that long event handlers do do skew the timing of the control requests.
...
Fixed USBtoSerial and Benito project SetLineEncoding calls failing if the USART is busy, due to the RX ISR delaying the control request handler.
2010-08-22 02:45:20 +00:00
81998ce297
Added compile time error to the AVRISP-MKII project when built for the U4 chips, as the default VTARGET detection ADC channel does not exist on these chips (thanks to Marco).
2010-08-22 01:42:09 +00:00
4f114e5766
Fixed MassStorage based demos and projects resetting the SCSI sense values before the command is executed, leading to missed SCSI sense values when the host retrieves the sense key (thanks to Martin Degelsegger).
...
Added missing DataflashManager_CheckDataflashOperation() function to the MassStorageKeyboard demo, removed redundant SCSI_Codes.h file as these values are part of the MassStorage Class Driver.
2010-08-18 10:33:21 +00:00
508e905d8d
Removed complicated logic for the Endpoint_ConfigureEndpoint() function to use inlined or function called versions depending of if the given bank size is a compile time constant, as the compiler does a better job of optimizing with basic code.
...
Changed over all device demos to use a clearer algorithm for the configuring of the application's endpoints.
2010-08-09 10:20:10 +00:00
9274610a48
Commit for the 100807 release.
2010-08-09 01:55:02 +00:00
5f3a1b2629
Fix invocations of avr-size in all makefiles broken on unpatched *nix systems, due to the recent update to the latest WinAVR makefile template.
2010-08-08 08:30:42 +00:00
98947e3750
Ensure all demos now compile in C99 standards mode, and not GNU99 (C99 + GNU extensions).
2010-08-03 11:13:06 +00:00
48c5cdced4
Hide the PROGMEM attribute from Doxygen, as it appears to confuse the parser in some situations.
2010-08-02 08:53:23 +00:00
ff09cf9c73
Fix XPLAINBridge project discarding characters from the USB interface due to a double read from the endpoint.
...
Make XPLAINBridge and USBtoSerial projects more reliable by forcing a flush if the UART-to-USB buffer becomes nearly full.
Reduce locking in the LightweightRingBuffer.h header files by only locking on the update of the buffer count, and require insertions and removals from each buffer to occur in only one execution thread.
Fix CDC_*_ReceiveByte() returning 0 when the interface is not configured, instead of the new -1 error value.
Fix CDC_Host_ReceiveByte() not re-freezing the pipe if no packet has been received.
Remove redundant Pipe token set commands in the CDC and RNDIS host class drivers.
2010-08-01 14:03:13 +00:00
fb0e6597b6
Invert the logic for the VBUS power light in the AVRISP-MKII project for the USBTINY-MKII board target.
2010-08-01 06:53:08 +00:00
9597b33c33
Fixed Serial peripheral driver not turning off the USART before reconfiguring it, which would cause incorrect operation to occur (thanks to Bob Paddock).
2010-07-31 06:55:47 +00:00
612df774d9
Oops - fix mixed "initialize" and "initialise" - opt for American spelling due to its wide use in technical standards.
2010-07-30 10:58:16 +00:00
0f45b9c8e0
More spell checking of all source files -- correct missed errors, switch to EN-GB spelling dictionary.
2010-07-30 09:48:35 +00:00
2034141a7e
Spell check more of the third party libraries used by LUFA.
2010-07-30 08:29:53 +00:00
24e621a8d8
Altered the CDC Deivice and Host Class drivers' receive byte routines, so that no data is indicated by a negative return value.
...
Added auto flushing of OUT data to the CDC Host Class driver's USBTask function to automatically flush the send pipe buffer.
2010-07-30 03:52:11 +00:00
7c8d16fd7a
Oops - need to turn off USART via control register B before reconfiguring, fix ordering of USART control register modifications in the Benito and USBtoSerial projects.
2010-07-30 01:11:04 +00:00
28401f7bb7
Spell check all source files once again to find any typos.
2010-07-29 16:20:45 +00:00
ca007f91f2
Fixed Benito and USBtoSerial projects not turning off the USART before reconfiguring it, which could cause incorrect operation to occur (thanks to Bob Paddock).
2010-07-29 15:14:56 +00:00
62022252ea
Add special support to the AVRISP-MKII for the new model USBTINY-MKII's additional LED to indicate target power source.
...
Add support to the USBTINY-MKII's additional LED in the board's LED driver header.
Changed LED indicator masks for the AVRISP-MKII project, so that there are defined roles for each LED.
2010-07-29 13:04:53 +00:00
30c2b620de
Remove obsolete macros and preprocessor checks from the AVRISP-MKII project's V2Protocol command handler header file.
2010-07-29 07:20:33 +00:00
de5b16909a
Added support to the AVRISP-MKII project for ISP speeds slower than 125KHz via a new software SPI driver.
...
Added new SPI_ORDER_* data order masks to the SPI peripheral driver.
2010-07-29 07:09:57 +00:00
be2a7d4598
Move over message ID specific header data to unions inside the standard TMC header structure, so that all header data is read in one chunk in the incomplete TMC demo.
2010-07-27 11:26:47 +00:00
cd39c38d5f
Rename reserved members of all structs so that they are uniformly named across all demos/projects/bootloaders.
...
Added start of the Incomplete TMC demo's command parser code.
2010-07-26 07:28:40 +00:00
0803cf00ac
Add missing INTERRUPT_CONTROL_ENDPOINT compile time option to the Mass Storage device projects/demos and incomplete Test and Measurement Class demo, which was accidentally removed during the makefile updates.
...
Alter Test and Measurement Class demo's request handlers to accept, process and correctly return the fields indicated in the specification.
2010-07-26 04:57:50 +00:00
4c9425c0d5
Added periodic flush timer to the Benito project. Alter the serial transmission code so that sent bytes do not block the remainder of the main program code from running.
2010-07-25 11:59:55 +00:00
2461ae508c
Future proof the XPROG protocol of the AVRISP-MKII project, so that non PDI and TPI requests return failure.
2010-07-22 12:34:32 +00:00
6bda628718
Update all demos, projects and bootloaders to indent all function parameters, one per line, for better readability.
...
Add missing const qualifiers to the demos.
2010-07-21 16:19:32 +00:00
97143bf814
Add missing const qualifiers to class drivers.
...
Indent core library function parameters so that there is only one parameter per line, to increase readability.
2010-07-21 14:00:51 +00:00
6b5e684c77
Update makefiles to use the latest WinAVR/Atmel toolchain makefile template.
...
Add new module source variables to the library core makefile, so that module sources can be added to a project's makefile on a per-module rather than per-file basis.
2010-07-19 14:00:44 +00:00
42ac34b484
Change over all makefiles to use C99 standards mode, rather than C99 + GNU Extensions.
2010-07-18 07:31:57 +00:00
9299735c75
Disable strict aliasing explicitly in the project makefiles, as this is apparently enabled by default in newer AVR-GCC builds, and aliasing is used heavily for type-punning through the LUFA and third party library's codebase.
2010-07-15 17:13:33 +00:00
f4710f6f86
Removed the automated checking of event names in the demo, project and bootloader makefiles due to inconsistancies between the behaviour of the command line tools used to perform the check on each platform.
...
Removed the internal endpoint and pipe memory allocation macros, as this is already performed directly in the code. Simplify the endpoint and pipe reset procedure.
2010-07-15 16:45:26 +00:00
dfe50ff349
Added ability to set the serial baud rate via the user's terminal in the XPLAINBridge project.
2010-07-15 11:01:31 +00:00
40631e9fe5
Fix pointer aliasing warning in the Mass Storage demos.
2010-07-15 10:34:29 +00:00
e2e1fe5aad
Fixed possible buffer overrun in the XPLAINBridge project when in serial bridge mode.
2010-07-15 04:45:31 +00:00
7cef08e10e
Fixed HID device class driver still using PrevReportINBuffer for GetReport control requests even when it has been set to NULL by the user application (thanks to Axel Rohde).
2010-07-15 01:42:36 +00:00
d83cc9ac80
Change AVRISP-MKII and XPLAINBridge descriptors to indicate that the device is bus-powered only. Add compile time options to reduce the compiled size of the firmware.
2010-07-13 14:17:18 +00:00
666c0fa4c3
Remove the timeout period extension code from the AVRISP project, as no single command should ever exceed the maximum timeout period. Extend timeout period to 1 second per command, so that an accidental timeout will never occur.
2010-07-13 11:26:03 +00:00
0313034245
Added const attributes to some of the class driver function parameters that were missing it.
2010-07-13 10:01:13 +00:00
3904c1a606
Add remaining AVRStudio project files to the library projects.
2010-07-13 04:39:54 +00:00
ac61b81a0b
Add first lot of AVRStudio project files for some of the library projects.
2010-07-13 04:32:33 +00:00
d3e00ce1ec
Rename the AVRISP main source files to AVRISP-MKII so that it matches the project name. Add AVRStudio project file for the AVRISP-MKII project.
2010-07-13 04:16:23 +00:00
ae9dab1398
Add missing clean_doxygen phony targets to the project makefiles.
2010-07-12 10:18:18 +00:00
8de31cbb78
Reduce prescaler of the flush timer in the USBtoSerial demo, so that buffer overruns will not occur regardless of hardware and baud rate settings.
2010-07-12 07:11:50 +00:00
0bcc82ac28
Alter the ring buffer library headers to have both atomic and non-atomic insertion/removal routines. Modify the existing projects so that buffer operations performed in an ISR use the shorted non-atomic versions, as they are already performed in a blocking ISR.
...
Alter USBtoSerial demo so that it does not enter a blocking loop to send data from the USB to the USART, as this can cause dropped bytes in the reception code if large amounts of data are sent in both directions at the same time. Added a flush timer to the USBtoSerial code for the USART to USB interface, so that multiple bytes can be sent in the same USB packet.
2010-07-12 07:04:19 +00:00
3fd246041b
Add glitch protection to the software UART in the XPLAINBridge project code, so that very short glitches on the RX line don't cause a frame reception to occur.
2010-07-12 02:23:11 +00:00
229935184b
Major changes to the XPLAINBridge software UART code for performance and reliability. New code reduces the number of missed characters and misread characters.
2010-07-11 14:14:08 +00:00
2b0d93c129
Correct misspellings in the Bluetooth demo code.
2010-07-11 08:11:25 +00:00
c326fe9605
Rewrote the implementation of the SwapEndian_16() and SwapEndian_32() functions so that they compile down in most instances to minimal loads and stores rather than complicated shifts.
...
Fixed SCSI.c implementations of all the demos/projects casting the block count to a 32-bit temporary before calling SwapEndian_16().
2010-07-09 07:24:34 +00:00
70983caea5
Move out Bluetooth stack callback functions to a seperate BluetoothEvents.c/.h set of files for clarity in the Incomplete BluetoothHost demo. Add a new stack callback for opened ACL channels, make the demo save the RFCOMM channel when opened so that it does not have to search for it on each iteration of the main program loop.
2010-07-08 07:44:07 +00:00
8b053d6ba5
Added new Drivers/USB/LowLevel/Device.c file to house Device mode specific functions that are more complicated than simple macros. Moved USB_Device_SendRemoteWakeup() to the new Device.c source file and corrected it to unfreeze and restart the USB controller clock before issuing a Remote Wakeup request.
...
Removed the USB_Device_IsRemoteWakeupSent() and USB_Device_IsUSBSuspended() macros, as they are now obsolete.
2010-07-02 03:37:19 +00:00
d29a408ffd
Add default "all" makefile targets to the demo tree makefiles.
2010-06-25 13:28:34 +00:00
016a4c068a
Make loops in AVRISP-MKII Clone project's XPROG protocol infinite rather than looping on the timeout value, as this is already checked inside the loop anyway.
2010-06-25 13:19:05 +00:00
55d7e1e65b
Make XPLAINBridge serial bridge much more reliable for the reception of characters from the XMEGA through the software UART interface.
2010-06-24 08:12:27 +00:00
ad29e79b94
Maximise the size of the ring buffers in the Benito/XPLAINBridge/USBtoSerial projects, so that they should never become full under normal conditions.
2010-06-24 07:42:18 +00:00
988604b25d
Moved calls to V2Params_UpdateParamValues() out of the main AVRISP-MKII and XPLAINBridge project loops and into the AVRISP management function.
2010-06-21 13:39:56 +00:00
51c2dcf3b0
Fixed broken PDI EEPROM Section Erase functionality in the AVRISP-MKII project.
2010-06-17 09:17:09 +00:00
711542ee89
Spell check code and manual pages. Remove custom Doxygen CSS stylesheet, as the new 1.7 Doxygen's default stylesheet is much better.
2010-06-16 11:01:01 +00:00
a14ece5f57
Change over Doxygen \note documentation to \pre where applicable.
2010-06-15 03:34:55 +00:00
27fb44268f
Update TemperatureDataLogger and Webserver projects to the latest FATFS library version.
2010-06-14 11:58:23 +00:00
d57e7369a2
Oops - temp code left in the XPLAINBridge project which prevented it from entering programmer mode.
2010-06-12 08:52:44 +00:00
036a156ff4
Slight improvements to the reliability of the software UART in the XPLAINBridge project.
2010-06-12 08:39:12 +00:00
5fa0e9c007
Oops - light weight ring buffer documentation used \ref instead of \param to document function parameters.
2010-06-10 01:30:32 +00:00
b02217d745
Add missing documentation to the lightweight ring buffer code in the XPLAINBridge project.
2010-06-10 01:26:10 +00:00
c2e340320c
Document lightweight ring buffer header files.
2010-06-06 13:49:50 +00:00
2dabb4e55f
Add the svn:eol-style property onto new files which where missing it to ensure uniform line endings.
2010-06-06 08:33:14 +00:00
6d53cdba83
More documentation fixes.
2010-06-03 15:55:28 +00:00
fc92f9969c
Minor documentation cleanups.
2010-06-03 15:32:45 +00:00
008e0e2e0a
Add start of RFCOMM service layer to the incomplete BluetoothHost demo.
...
Reduce the size of the attribute search list from 15 ranges to 8 to save RAM.
2010-06-03 03:58:57 +00:00
3b95b8dedc
Added new VTARGET_REF_VOLTS and VTARGET_SCALE_FACTOR compile time defines to the AVRISP-MKII programmer project to set the VTARGET reference voltage and scale factor.
...
Fixed XPLAINBridge project not correctly reading the XMEGA's supply voltage when reporting back to the host.
2010-05-27 10:36:21 +00:00
8d993afc53
Replace ring buffer library in Benito and USBtoSerial projects with the new lightweight ring buffer header to improve reliability.
2010-05-26 13:26:10 +00:00
670413603f
The EEPROM stream read/write functions now use eeprom_update_byte() instead of eeprom_write_byte(), so that only changed bytes are written to EEPROM to preserve its lifespan.
...
Changed over the AVRISP-MKII and TemperatureDataLogger projects to use eeprom_update_byte() when writing non-volatile parameters to EEPROM to preserve its lifespan.
2010-05-26 11:54:55 +00:00
bb9fb1051c
Add better documentation to the Software UART code in the XPLAINBridge project.
2010-05-26 08:10:35 +00:00
1c407b9669
Switch software UART over to timer 1 and remove timer prescaling to try to prevent integer rounding errors and thus minimize the possible error of the UART code.
2010-05-26 07:51:25 +00:00
f64e3db07a
Rename software USART driver globals to make the code more in line with the rest of the XPLAINBridge project.
2010-05-26 07:35:27 +00:00
79742c5d24
Make software USART used in the XPLAINBridge project directly check and store into the ring buffers, rather than polling from the main program loop to avoid added latency.
2010-05-26 06:59:55 +00:00
9b29d1dc50
Create a new LightweightRingBuffer.h header file for the XPLAIN project to abstract out the new ring buffer without a performance penalty.
2010-05-26 06:35:02 +00:00
9c037a952f
The RingBuff library code has been replaced in the XPLAINBridge project with an ultra lightweight buffer to help improve the reliability of the bridge.
2010-05-26 06:15:05 +00:00
776485a6c5
Remove obsolete entry from the Doxygen configuration files.
2010-05-23 08:39:02 +00:00
3e515cdfa8
Short UUIDs are measured in bytes, not bits -- update Service Discovery Protocol code so that it can now correctly match against UUIDs in the service table.
2010-05-20 13:06:04 +00:00
a883cf65dc
Renamed CDC device class demos' ManagementEndpoint descriptor to NotificationEndpoint to more accurately indicate its purpose.
2010-05-20 06:15:21 +00:00
f13bc35a19
Begin processing code for Service Discovery Protocol attributes.
2010-05-17 23:36:05 +00:00
ff61dfa505
Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).
2010-05-16 05:43:03 +00:00
80d85090ba
Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from the last page of FLASH.
2010-05-14 10:11:40 +00:00
34047efc7e
Remove incorrect check for the current device state in the Set Configuration request handler of DevChapter9, which broke Set Configuration requests to the device under most circumstances.
...
Move out the SPI prescaler list to a PROGMEM module-level variable in ISPTarget.c.
2010-05-13 12:57:49 +00:00
571159df1b
Additional fix to the AVRISP-MKII clone project for 256KB AVRs.
2010-05-13 11:14:10 +00:00
cd0093a14b
Fixed AVRISP-MKII clone project not correctly issuing SET EXTENDED ADDRESS commands when the extended address boundary is crossed during programming or readback (thanks to Gerard Sexton).
...
Fixed warnings when building the AVRISP-MKII clone project with the ENABLE_XPROG_PROTOCOL compile time option disabled.
2010-05-13 09:25:17 +00:00
d3c623e1e1
The LIBUSB_FILTERDRV_COMPAT compile time option in the XPLAINBridge and AVRISP-MKII projects has been renamed LIBUSB_DRIVER_COMPAT, as it applies to all software on all platforms using the libUSB driver.
...
Fix Benito makefile which was accidentally changed during testing.
2010-05-13 07:31:27 +00:00
e277ff0cf4
Removed TeensyHID bootloader, per request from Paul at PJRC.
2010-05-12 11:12:53 +00:00
05ac59d0ee
Add new ReportType parameter to the HID class driver device callback and host report sending routines.
...
Renamed internal Host mode Class driver descriptor comparator callback routines so that they all start with a uniform DCOMP_{Class Abbreviation}_ prefix.
2010-05-09 06:01:01 +00:00
071e02c6b6
Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.
2010-05-08 03:12:14 +00:00
e331b531c6
Change over instances of "make" in the makefiles to "$(MAKE)" to allow for the make tool to be overridden.
2010-05-07 07:11:25 +00:00
57fe6b4fb9
Don't cast the line encoding baud rate to a uint16_t before performing the baud rate calculation in the Benito project.
2010-05-07 06:49:31 +00:00
27eb17cb93
Change over unix line-endings to dos line endings.
2010-05-07 06:40:47 +00:00
9c8bd6ed9b
Remove incorrect Abstract Call Management class specific descriptor from the CDC demos, bootloaders and projects.
2010-05-06 11:32:55 +00:00
ab8668b14e
Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.
2010-05-04 11:33:51 +00:00
27f0ba6fc3
Fixed device state not being reset back to the default state if the host sets the address to 0x00.
...
Fixed Set Configuration requests not being stalled until the host has set the device's address.
Fixed possibility of internal signature retrieval being corrupted if an interrupt occurs during a signature byte read (thanks to Andrei Krainev).
2010-05-04 10:07:22 +00:00
eed7d4df6a
Added new ENDPOINT_*_BusSuspended error code to the Endpoint function, so that the stream functions early-abort if the bus is suspended before or during a transfer.
2010-05-03 07:41:22 +00:00
5c0c0327d5
Increase hardware PDI/TPI programming speed to 1MHz in the AVRISP MKII clone project.
2010-05-02 06:18:42 +00:00
a5e79333e5
Switch back to C based timeout ISR in the AVRISP project - assembly version was failing, and only one or two cycles could be shaved off the compiler generated code.
2010-05-02 06:02:54 +00:00
3d28d53c3e
Change AVRISP project's timeout to be interrupt based again, but make the interrupt itself interruptable and use a seperate assembly file to hand-optimize the ISR code.
...
Removed the cast to uint16_t on the set baud rate in the USBtoSerial project, so that the higher >1M baud rates can be selected (thanks to Steffan).
2010-05-02 05:16:34 +00:00
9a1560dc05
Make sure that long reads are aborted early if the connection times out while waiting on more bytes in the AVRISP MKII clone project.
2010-04-30 08:33:21 +00:00
ceb16ee24f
Make sure that the NVM bus/controller busy waits in the AVRISP MKII clone project abort properly if a timeout occurs while waiting for a response.
2010-04-30 08:27:21 +00:00
e977774d4e
Relocate USBInterrupt.c/.h from the HighLevel USB driver directory to the LowLevel directory as it is hardware-dependent.
2010-04-28 08:15:16 +00:00
59c4871f80
USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.
2010-04-28 07:48:26 +00:00
85aaaf84ce
Make AVRISP-MKII clone project's software PDI/TPI mode more robust by keeping track of timeouts while waiting for a Tx/Rx to finish.
2010-04-28 06:33:48 +00:00
5993e1efe7
Added ability to search by Channel PSM to the GetChannelData() function in the BluetoothHost demo.
...
Added new HCI states to properly initialize the bluetooth dongle and retrieve the local BDADDR.
Factored out Bluetooth state information into a new state structure for easy reference in the user application.
Added new StackInitialized() Bluetooth stack callback function.
2010-04-22 14:08:00 +00:00
fc8e4837a9
Add const keyword to the demo function parameters where possible.
2010-04-18 12:10:30 +00:00
5e14c194c9
Fixed Set/Clear Feature requests directed to a non-configured endpoint not returning a stall to the host.
...
Make TeensyHID bootloader use an 8 byte control endpoint to match the official Teensy, just in case Paul decides to authenticate on that attribute in the future.
2010-04-14 13:46:49 +00:00
e55f338663
Document the Bluetooth ACL layer. Remove unneeded parameters from the signalling command processing routines.
...
Change over the code so that the bluetooth packet data is read in by the stack rather than the user application, to make it more unform for sending/receiving, and so the library can handle incomming fragmentation in the future.
Start Service Discovery Protocol decoding and processing.
2010-04-13 11:19:04 +00:00
ee74b4948f
Add information request/response signal handler to the Bluetooth Host demo.
...
Ensure that the AVRISP-MKII project's Windows avrdude compatibility define is named properly in all parts of the code.
2010-04-06 02:48:47 +00:00
fa1a092901
Add user callback function to the Bluetooth host demo to filter out connections from remote devices. Add in ability to reject connections based on their bluetooth device address.
...
Clean up RelayBoard project code.
Make AVRISP project clear the XMEGA target's reset register twice; this does not appear to take affect properly the first time under some circumstances.
2010-04-05 08:09:12 +00:00
fd96b28882
More improvements to the incomplete BluetoothHost demo - add Disconnection Event processing.
...
Remove unused macro in the host mode demos for the maximum Configuration Descriptor size.
2010-04-01 04:30:21 +00:00
c9148f9b47
Added WIN_LIBUSB_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows builds of avrdude at the expense of AVRStudio compatibility.
2010-03-31 09:20:24 +00:00
ce46257ff2
Add RelayBoard project patch from OBinou.
2010-03-31 06:44:54 +00:00
3790907f4d
Added board hardware driver support for the Benito programmer.
2010-03-30 09:08:26 +00:00
9257f4ab8e
Add briefs for the library core structures.
2010-03-29 13:32:36 +00:00
74353374c3
All Class Driver Host mode demos now correctly set the board LEDs to READY once the enumeration process has completed.
...
Fixed Still Image Host class driver not resetting the transaction ID when a new session is opened, fixed driver not sending a valid session ID to the device.
2010-03-25 06:34:38 +00:00
b8db5fc1e7
Added new Relay Controller Board project (thanks to OBinou).
...
Added hardware board driver support for the PJRC Teensy line of USB AVR boards.
2010-03-24 08:06:23 +00:00
f79f9abd28
Fixed compilation error in the AudioInput demos when MICROPHONE_BIASED_TO_HALF_RAIL is defined (thanks to C. Scott Ananian).
...
Minor documentation cleanups.
Make sure HID class driver uses properly cast pointers when writing to the report buffer.
2010-03-24 05:50:09 +00:00
4e99625f7c
Change over MIDIToneGenerator to use only a single channel (MIDI channel 1) due to cycle constraints.
2010-03-23 10:09:49 +00:00
c58c53dba9
Added incomplete MIDIToneGenerator project.
2010-03-23 09:16:47 +00:00
49b09a2042
Standardized the naming scheme given to configuration descriptor sub-elements in the Device mode demos, bootloaders and projects.
...
Fix errors in the MouseHostWithParser demo from incorrect use of the HID_ALIGN_DATA() macro.
2010-03-22 07:12:25 +00:00
5227ca4ce2
Double bank CDC endpoints in the XPLAIN Bridge project, re-enable JTAG once the mode selection pin has been sampled.
2010-03-21 12:21:13 +00:00
72527867f6
Remove redundant check in the software PDI programming code of the AVRISP project.
2010-03-17 13:07:22 +00:00
9a5ae36a4f
Software PDI mode breaks unless the software USART has 100 cycles between bits.
2010-03-17 11:48:39 +00:00
7d51e51c79
Increased throughput of the USBtoSerial demo on systems that send multiple bytes per packet (thanks to Opendous Inc.).
2010-03-16 12:14:09 +00:00
2b74b517ea
Don't enable the pullup on the target /RESET line in the AVRISP project for PDI mode - clearing the XMEGA's reset control register twice is enough to release it from reset. Possible silicon bug, since the official Atmel programmers have the same issue.
2010-03-16 12:09:22 +00:00
39d56aeffe
Fixed PDI programming mode in the AVRISP programmer project not exiting programming mode correctly (clear target Reset key twice, set /RESET pin to pullup).
...
Add newlines to the MIDI event printf() statements in the MIDI host demos.
2010-03-16 11:47:11 +00:00
aca7863350
Added ENABLE_TELNET_SERVER compile time option to the Webserver project to disable the TELNET server if desired.
...
Change over static strings in the Webserver project to use PROGMEM where possible.
2010-03-10 12:48:20 +00:00
92418433a5
Fix incorrect LED mask name in the Webserver project.
...
Fix missing text from the Host Mode States enum documentation.
2010-03-09 13:22:51 +00:00
ce260ae786
Webserver project now uses the board LEDs to indicate the current IP configuration state.
...
Don't double-read data from the attached disk in the incomplete StandaloneProgrammer project when in host mode.
2010-03-09 05:15:08 +00:00
c0c982df7a
Added a timeout value to the TWI_StartTransmission() function, within which the addressed device must respond.
...
Fixed TWI_StartTransmission() corrupting the contents of the GPIOR0 register.
2010-02-24 09:49:19 +00:00
071fd8ce53
Revert changes made for the partial port to the AVR32 architecture.
2010-02-24 06:58:23 +00:00
e11fddfe66
Update Temperature board driver to be AVR32 compatible when the ADC peripheral driver is eventually ported. Make architecture includes explicit for both the AVR32 and the AVR8, to make way for future architecture ports.
...
Add SPI driver aliases for the old function names in the AVR8 driver, so that existing code will still compile against the new version.
2010-02-23 03:51:17 +00:00
c24027f3b5
Fixed software PDI/TPI programming mode in the AVRISP project not correctly toggling just the clock pin.
...
Fix broken AVR8 Serial peripheral driver.
2010-02-23 01:03:27 +00:00
d2851b3351
Oops - need to revert changes made to ease testing of the software PDI programming mode.
2010-02-21 22:15:52 +00:00
5e12d436fa
Remove dual ISR for software PDI mode, use a single ISR instead to reduce code complexity.
2010-02-21 22:11:49 +00:00
e322f14620
More fixes to the AVRISP command timeout system so that it should no longer lock up while processing command no matter what the conditions.
2010-02-21 06:26:33 +00:00
12a01ed72d
Increased the speed of both software and hardware TPI/PDI programming modes of the AVRISP project.
2010-02-21 05:44:12 +00:00
10b9394a8b
Oops - missed a few references to the old global TimeoutMSRemaining counter in ISPTarget.c of the AVRISP-MKII clone project.
2010-02-20 12:17:48 +00:00
ce8d0424b1
AVRISP programmer project now has a more robust timeout system, allowing for a doubling of the software USART speed for PDI and TPI programming.
2010-02-19 05:17:41 +00:00
04d40897cf
Commit for the 100219 release.
2010-02-19 00:07:22 +00:00
42b850f2b9
Use a temporary variable to hold the current URI length in the Webserver, rather than calling strlen() multiple times on an unchanged buffer. Clean up uip-split.c.
2010-02-18 05:33:35 +00:00
012628f635
Turn OFF double banking in the Webserver demo - leaving it on seems to destroy the system throughput.
2010-02-18 05:10:24 +00:00
3b6987bca3
Add uIP-split code to the Webserver project, so that each packet is split in half to avoid the delayed-ACK problem when communicating with other devices. Condense HTTP server code, so that the HTTP headers are all sent from the one state. Make default filename append to any directory URI, rather than just the root directory.
2010-02-18 02:19:43 +00:00
c77b30e9e6
Clean up XPLAINBridge code.
2010-02-16 13:12:59 +00:00
015956baba
Oops - missing brackets in the declaration of a string in TELNETServerApp.c.
2010-02-15 13:50:04 +00:00
96a12cd12c
Add missing TWI_Init() call to the TemperatureDataLogger project. Make DUMMY_RTC compile time option the default, so that it works correctly on the USBKEY and other Atmel boards out of the box.
2010-02-15 13:40:53 +00:00
de0ccb3d09
Add NO_VTARGET_DETECT compile time option to the AVRISP-MKII clone project, to disable VTARGET detection on AVR models with an on-chip ADC.
2010-02-13 03:21:28 +00:00
c6f21fde62
Speed up Webserver demo data rate by not sending a full ethernet frame each time, preventing the receiver from using a delayed ACK scheme which slows down the connection. TELNET server cleanup.
2010-02-12 07:54:28 +00:00
8154331da6
Move DHCP negotiation timer into the DHCP connection application state structure, so that each connection gets its own timeout counter (only one connection currently used, but this way is more correct). Add const correctness to static data in the TELNETServerApp.c and HTTPServerApp.c files.
2010-02-12 07:27:26 +00:00
41ef05a6e5
Fix DHCPClient init code in the Webserver project writing to the incorrect application state location (thanks to Mike Alexander).
2010-02-12 05:05:03 +00:00
3a2c1db675
Fixed lack of SECTION ERASE command in TPI programming mode of the AVRISP project preventing fuses from being cleared.
2010-02-10 04:07:06 +00:00
ab195ab1da
Added .5MHz recovery clock to the AVRISP programmer project when in ISP programming mode to correct mis-set fuses.
...
Fixed AVRISP project not extending the command delay after each successful page/word/byte program.
2010-02-10 04:02:10 +00:00
35a0fe9384
Fixed USB_GetHIDReportSize() returning the number of bits in the specified report instead of bytes.
...
Moved the USB_GetHIDReportItemInfo() calls into the main report item passing loop in the *HostWithParser demos - it is fast enough not to effect performance, and avoids duplicate code.
Make Webserver project report the LUFA version as part of the HTTP header.
2010-02-09 12:30:51 +00:00
3ab0b3a027
Fix LowLevel Keyboard demo -- accidentally trying to dereference a uint8_t type in ProcessLEDReport().
2010-02-08 03:32:31 +00:00
7ae91099e9
Fix AVRISP-MKII clone project's TPI Chip Erase command processing - ensure erase location is the high byte in the given address space, check NVMBUSY for completion rather than the NVM Bus Enable bit.
...
Change If-Else chains over to switch statements in XPROGProtocol.c for clarity.
2010-02-08 03:16:09 +00:00
1fdc0e664e
Make Webserver allow HTTP requests for files with up to 50 characters in the path instead of 30, to be in synch with the project documentation.
...
Change Webserver project's ENABLE_DHCP compile time option to ENABLE_DHCP_CLIENT to more accurately indicate its function.
2010-02-07 10:46:02 +00:00
15f84bb8f5
New BOARD value option BOARD_NONE (equivelent to not specifying BOARD) which will remove all board hardware drivers which do not adversely affect the code operation (currently only the LEDs driver).
...
Spell-check code/comments in the Webserver/AVRISP-MKII projects.
2010-02-04 02:27:09 +00:00
f4f44f9fc1
Re-add Webserver uIP application polling, apply patch to uIP by Andrew Ruder to fix corrupt TCP streams when multiple applications are used and the applications are polled for more data.
2010-02-03 14:09:56 +00:00
7d3ed40070
Fix TELNET server locking up if an invalid command was issued.
2010-02-03 13:08:37 +00:00
b9cf4815e5
Disable uIP connection polling for now - this seems to corrupt the buffers.
2010-02-03 11:31:59 +00:00
16ea5aa7a2
Add a TELNET server to the webserver project, which currently can list active TCP connections.
2010-02-03 10:39:33 +00:00
77e86e7d82
Exlude the "INCLUDE_FROM_*" macros from the individual project's documentation.
2010-02-03 00:57:49 +00:00
08e8d6393e
Exclude FATFs from the Webserver project documentation. Rename the functions in the HTTPServerApp.c/.h files so that they use the correct "HTTPServerApp_" prefix, and not "Webserver_".
2010-02-03 00:48:06 +00:00
53eca61d02
Minor fixups to the documentation and preprocessor tokens.
2010-02-02 13:29:07 +00:00
f979fd36be
Remove now unused conf directory from the uIP stack in the Webserver project.
2010-02-02 12:56:29 +00:00
84e1241f80
Replace the Webserver demo's uIP with the latest code ripped from the Contiki project by Adam Dunkels.
2010-02-02 12:51:05 +00:00
1008260985
Make packet processing code in the Webserver project a bit neater using a switch statement instead of an if-else-if chain.
2010-02-02 05:56:47 +00:00
5687ac7316
Fix TPI mode chip erase code not properly erasing the target memory space.
2010-02-02 04:33:58 +00:00
8d49480891
Oops - new Write Word alignment code in the TPI programming function means that the WriteBuffer parameter is no longer const.
2010-02-02 03:46:49 +00:00
ec6fbb219f
Make TPI writes add a dummy high byte if the data isn't word-aligned.
2010-02-02 03:27:28 +00:00
b736a5ef2b
Make TPI programming protocol program in words, not bytes to satisfy the datasheet conditions.
2010-02-02 03:22:45 +00:00
4d246a82cb
Fixed incorrect values of USB_CONFIG_ATTR_SELFPOWERED and USB_CONFIG_ATTR_REMOTEWAKEUP tokens (thanks to Claus Christensen).
...
Mark the AVRISP-MKII project descriptors as being both Bus Powered and Device Powered.
Copy over file level documentation of the peripheral drivers to the module level documentation.
2010-02-01 12:35:48 +00:00
9e7ffcb014
Make AVRISP XPROG function parameters const where possible.
2010-02-01 05:34:59 +00:00
5f363996e3
Fixed issues with EEPROM and FLASH ISP programming in the AVRISP project.
2010-02-01 03:42:10 +00:00
b6a4584a19
Fixed Pipe_IsEndpointBound() function not taking the endpoint's direction into account.
...
Re-added Pipe_IsEndpointBound() calls to the CDC and RNDIS host class drivers, not that the function has the correct behaviour for devices with bidirectional endpoints.
2010-02-01 01:27:00 +00:00
bb1a036f09
Clean up HTTP webserver code in the Webserver project, so that it follows the uIP application structure guidelines and uses cleaner state machine based code.
2010-01-31 14:18:03 +00:00
331e8dece6
Use _delay_us() function in the XPROGTarget.c file to ensure timing requirements are met, rather than a fixed number of NOPs.
2010-01-31 12:33:04 +00:00
75d27f8ef0
Oops - PDI handshake delay was too long, causing the device's /RESET functionality to be re-enabled.
2010-01-31 12:25:53 +00:00
97f7cd947b
Better HTTP GET parsing in the Webserver demo, add application polling.
2010-01-31 04:23:55 +00:00
e8b8ed2bad
Add TCP retransmission support to the HTTP webserver in the Webserver project, so that lost segments are retransmitted as needed.
2010-01-29 09:21:38 +00:00
254a0c1ae8
Update driver INF files - change manufacturer name from the original template's name to the Four Walled Cubicle website.
2010-01-29 06:32:20 +00:00
a114878209
Oops - TPI programming is broken in the AVRISP project because the busy-flag check wasn't inverting the result.
2010-01-29 06:02:02 +00:00
872f61ff53
Fix TPI communications in the AVRISP project when bit-banged USART mode is selected.
2010-01-29 05:31:25 +00:00
fa3135d485
Add MIME type handling to the Webserver project, so that files of different types (e.g. images) can be served out to HTTP clients.
2010-01-29 02:43:07 +00:00
1b59f561ed
Second fix to Webserver project's makefile for the FATFs path case to fix *nix builds.
2010-01-28 13:25:50 +00:00
e4674aecb7
Delete FATFs .lst files from the Webserver project, accidentally committed.
2010-01-28 13:24:04 +00:00
1babe52682
Oops - fix path case in the Webserver project makefile, to fix *nix builds.
2010-01-28 13:23:05 +00:00
5f776f4785
Fix up project documentation files' overview tables, so that multiple items occupy multiple lines in the same cell, rather than multiple cells.
2010-01-28 13:17:36 +00:00
d11ed10c53
Add FatFS library to the Webserver project, extend the HTTP server so that it now serves files from the Dataflash. Add Mass Storage device mode class driver so that files can be loaded to the board Dataflash when inserted into a PC.
2010-01-28 12:47:35 +00:00
cec699ac59
Clean up Webserver project - add more Doxygen documentation for the new DHCP client functions and defines.
2010-01-27 13:45:08 +00:00
a960e4b3b2
Add DHCP server to the Webserver demo for automatic network configuration. Correct uIP timer clock not tracking the correct timespan.
2010-01-27 13:15:49 +00:00
1aeb5056d6
Ensure TPI enable timing requirements are met in AVRISP-MKII programmer. Remove invalid code in the TPI read/write functions.
2010-01-27 03:45:15 +00:00
2059fd8b1a
Manually pull PDI clock pin high for 1ms before disabling PDI mode in the AVRISP-MKII project, to ensure that the PDI bus is disabled in the target and /RESET functionality restored.
2010-01-27 02:59:54 +00:00
eb99b1ec90
Exclude host application directories from the Doxygen input source file directories.
2010-01-25 13:20:46 +00:00
4f96283761
Add missing AVRISPDescriptors.c/.h files to the XPLAINBridge project.
2010-01-25 13:07:54 +00:00
4bd44139b1
Move TWI.c driver into the straight LUFA/Drivers/Peripheral/ directory.
...
Fix TemperatureDataLogger and Webserver project builds.
2010-01-25 13:02:25 +00:00
db420853ce
Add Webserver project Doxygen configuration file and overview document.
...
Fix Doxygen configuration files' input file exclusion filters.
2010-01-25 12:46:57 +00:00
15c408ab86
Moved initial completed version of the Webserver project out of the Projects/Incomplete directory.
2010-01-25 12:10:13 +00:00
d66f227cce
Neaten Webserver project code.
2010-01-25 12:01:02 +00:00
431db89b00
Fixed CDC and RNDIS host demos and class drivers - bidirectional endpoints should use two seperate pipes, not one half-duplex pipe.
2010-01-25 11:50:41 +00:00
74b6993d66
Cleanup and partially fix AVRISP-MKII project's TPI programming support.
2010-01-25 04:13:44 +00:00
857381185d
ADC2 and ADC3 channels do not exist on the U4 series USB AVRs.
2010-01-25 02:15:27 +00:00
5d5e359076
Minor code cleanups, remove TemperatureDataLogger host application's Visual Studio Solution files, add LibHIDNet license files.
2010-01-25 01:27:06 +00:00
b68f7f1649
Added explicit ADC channel masks for the standard set of ADC channels, as the single-ended channel MUX masks are not equal to the channel number on some AVR models. Changed demos to use the new channel masks when using the ADC driver.
2010-01-25 00:52:45 +00:00
871d9bf1af
Fixed DFU bootloader programming not discarding the correct number of filler bytes from the host when non-aligned programming ranges are specified (thanks to Thomas Bleeker).
2010-01-24 13:38:20 +00:00
dd995683ea
Enhance TemperatureDatalogger project -- add RTC capabilities so that data is logged along with the current time and date. Make logging interval configurable, set by a C# PC host application.
2010-01-24 11:13:23 +00:00
Dean Camera