f2324fc2b4
Second patch to fix incorrect PDI/TPI programming speed.
2010-11-14 06:44:57 +00:00
d41cd9a41a
Fixed PDI/TPI programming speed of ~250KHz in the AVRISP-MKII Clone project, instead of the desired 500KHz.
2010-11-12 06:24:01 +00:00
50390867e7
Fixed incorrect PollingIntervalMS values in the demo/project/bootloader endpoint descriptors (thanks to MCS Electronics).
2010-11-10 12:38:25 +00:00
0ce2950d81
Added board hardware driver support for the Adafruit U4 breakout board.
...
Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.
Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).
2010-11-08 03:41:48 +00:00
5ce8380a7d
Fix XPLAINBridge code broken during the changes to the Rescue Clock generation in the AVRISP-MKII clone project.
...
Change over all low level host mode project's descriptor comparator routines to perform the descriptor casting in a temp variable to make the code clearer and easier to modify (despite being more verbose).
2010-11-02 11:16:36 +00:00
3bf760ad7d
Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times when 125KHz ISP programming mode is selected.
2010-11-02 07:57:23 +00:00
cb779e3d7d
Changed over www.fourwalledcubicle.com links to the new www.lufa-lib.org redirect domain, including the new aliased links for LUFA-related pages such as the various download/source control mirrors and support lists.
2010-10-28 06:08:58 +00:00
55538dcef3
Add descriptor class, subclass and protocol constants to the class drivers, modify all demos to use them where possible.
...
Move out private/internal host class driver constants to the common class driver headers, so that they can be used in the Low Level host mode demos.
Ensure all demos, projects and bootloaders use the class driver constants where possible to minimise code repetition.
2010-10-25 12:42:55 +00:00
5a4def7478
Clean up excessive whitespace at the end of each line using the wspurify tool made by Laszlo Monda
2010-10-13 14:05:35 +00:00
93793679c9
Revert change to the AVRISP-MKII project for fuse byte programming via the CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.
2010-10-02 10:07:24 +00:00
a447ae134f
Fixed broken lock byte programming in the AVRISP-MKII clone project for some XMEGA targets.
2010-10-02 10:02:24 +00:00
824ce10390
Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used.
2010-10-02 08:41:08 +00:00
a509729b2d
Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive.
...
Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set.
2010-09-29 13:56:52 +00:00
800485bd95
Remove dfu-programmer program switches, to ensure maximum compatibility with all dfu-programmer versions.
2010-09-24 06:59:28 +00:00
bd85422d2b
Added the --suppress-bootloader-mem option to the makefile dfu target, to ensure that writes to the bootloader section of the AVR's flash memory are ignored (thanks to Axel Rohde).
...
Fixed incorrect command name for EEPROM memory programming in the makefile dfu-ee target.
Makefile whitespace fixes.
2010-09-24 06:45:11 +00:00
6d2f091cec
Make project makefiles correctly clean intermeditary build files from assembly and C++ sources (thanks to Daniel Czigany).
2010-09-15 03:00:29 +00:00
fdcb486e22
Fix typos in the project overview text files.
2010-09-09 13:39:52 +00:00
4dece08bef
Clarify in the project documentation files what the each of the different USB AVR device "series" comprises of.
2010-08-31 12:33:21 +00:00
009eebf229
Fix incorrect ADC driver documentation for the parameters of ADC_Init(), fix incorrect call to ADC_Init() in the TemperatureDatalogger project.
2010-08-31 07:32:48 +00:00
092f82e06f
Changed the signature of the CALLBACK_USB_GetDescriptor() callback function so that the descriptor pointer is const, to remove the need for extra casting inside the callback (thanks to Jonathan Kollasch).
2010-08-24 13:02:38 +00:00
81998ce297
Added compile time error to the AVRISP-MKII project when built for the U4 chips, as the default VTARGET detection ADC channel does not exist on these chips (thanks to Marco).
2010-08-22 01:42:09 +00:00
508e905d8d
Removed complicated logic for the Endpoint_ConfigureEndpoint() function to use inlined or function called versions depending of if the given bank size is a compile time constant, as the compiler does a better job of optimizing with basic code.
...
Changed over all device demos to use a clearer algorithm for the configuring of the application's endpoints.
2010-08-09 10:20:10 +00:00
9274610a48
Commit for the 100807 release.
2010-08-09 01:55:02 +00:00
5f3a1b2629
Fix invocations of avr-size in all makefiles broken on unpatched *nix systems, due to the recent update to the latest WinAVR makefile template.
2010-08-08 08:30:42 +00:00
48c5cdced4
Hide the PROGMEM attribute from Doxygen, as it appears to confuse the parser in some situations.
2010-08-02 08:53:23 +00:00
fb0e6597b6
Invert the logic for the VBUS power light in the AVRISP-MKII project for the USBTINY-MKII board target.
2010-08-01 06:53:08 +00:00
0f45b9c8e0
More spell checking of all source files -- correct missed errors, switch to EN-GB spelling dictionary.
2010-07-30 09:48:35 +00:00
28401f7bb7
Spell check all source files once again to find any typos.
2010-07-29 16:20:45 +00:00
62022252ea
Add special support to the AVRISP-MKII for the new model USBTINY-MKII's additional LED to indicate target power source.
...
Add support to the USBTINY-MKII's additional LED in the board's LED driver header.
Changed LED indicator masks for the AVRISP-MKII project, so that there are defined roles for each LED.
2010-07-29 13:04:53 +00:00
30c2b620de
Remove obsolete macros and preprocessor checks from the AVRISP-MKII project's V2Protocol command handler header file.
2010-07-29 07:20:33 +00:00
de5b16909a
Added support to the AVRISP-MKII project for ISP speeds slower than 125KHz via a new software SPI driver.
...
Added new SPI_ORDER_* data order masks to the SPI peripheral driver.
2010-07-29 07:09:57 +00:00
2461ae508c
Future proof the XPROG protocol of the AVRISP-MKII project, so that non PDI and TPI requests return failure.
2010-07-22 12:34:32 +00:00
6bda628718
Update all demos, projects and bootloaders to indent all function parameters, one per line, for better readability.
...
Add missing const qualifiers to the demos.
2010-07-21 16:19:32 +00:00
6b5e684c77
Update makefiles to use the latest WinAVR/Atmel toolchain makefile template.
...
Add new module source variables to the library core makefile, so that module sources can be added to a project's makefile on a per-module rather than per-file basis.
2010-07-19 14:00:44 +00:00
42ac34b484
Change over all makefiles to use C99 standards mode, rather than C99 + GNU Extensions.
2010-07-18 07:31:57 +00:00
9299735c75
Disable strict aliasing explicitly in the project makefiles, as this is apparently enabled by default in newer AVR-GCC builds, and aliasing is used heavily for type-punning through the LUFA and third party library's codebase.
2010-07-15 17:13:33 +00:00
f4710f6f86
Removed the automated checking of event names in the demo, project and bootloader makefiles due to inconsistancies between the behaviour of the command line tools used to perform the check on each platform.
...
Removed the internal endpoint and pipe memory allocation macros, as this is already performed directly in the code. Simplify the endpoint and pipe reset procedure.
2010-07-15 16:45:26 +00:00
d83cc9ac80
Change AVRISP-MKII and XPLAINBridge descriptors to indicate that the device is bus-powered only. Add compile time options to reduce the compiled size of the firmware.
2010-07-13 14:17:18 +00:00
666c0fa4c3
Remove the timeout period extension code from the AVRISP project, as no single command should ever exceed the maximum timeout period. Extend timeout period to 1 second per command, so that an accidental timeout will never occur.
2010-07-13 11:26:03 +00:00
d3e00ce1ec
Rename the AVRISP main source files to AVRISP-MKII so that it matches the project name. Add AVRStudio project file for the AVRISP-MKII project.
2010-07-13 04:16:23 +00:00
ae9dab1398
Add missing clean_doxygen phony targets to the project makefiles.
2010-07-12 10:18:18 +00:00
70983caea5
Move out Bluetooth stack callback functions to a seperate BluetoothEvents.c/.h set of files for clarity in the Incomplete BluetoothHost demo. Add a new stack callback for opened ACL channels, make the demo save the RFCOMM channel when opened so that it does not have to search for it on each iteration of the main program loop.
2010-07-08 07:44:07 +00:00
8b053d6ba5
Added new Drivers/USB/LowLevel/Device.c file to house Device mode specific functions that are more complicated than simple macros. Moved USB_Device_SendRemoteWakeup() to the new Device.c source file and corrected it to unfreeze and restart the USB controller clock before issuing a Remote Wakeup request.
...
Removed the USB_Device_IsRemoteWakeupSent() and USB_Device_IsUSBSuspended() macros, as they are now obsolete.
2010-07-02 03:37:19 +00:00
d29a408ffd
Add default "all" makefile targets to the demo tree makefiles.
2010-06-25 13:28:34 +00:00
016a4c068a
Make loops in AVRISP-MKII Clone project's XPROG protocol infinite rather than looping on the timeout value, as this is already checked inside the loop anyway.
2010-06-25 13:19:05 +00:00
988604b25d
Moved calls to V2Params_UpdateParamValues() out of the main AVRISP-MKII and XPLAINBridge project loops and into the AVRISP management function.
2010-06-21 13:39:56 +00:00
51c2dcf3b0
Fixed broken PDI EEPROM Section Erase functionality in the AVRISP-MKII project.
2010-06-17 09:17:09 +00:00
711542ee89
Spell check code and manual pages. Remove custom Doxygen CSS stylesheet, as the new 1.7 Doxygen's default stylesheet is much better.
2010-06-16 11:01:01 +00:00
a14ece5f57
Change over Doxygen \note documentation to \pre where applicable.
2010-06-15 03:34:55 +00:00
fc92f9969c
Minor documentation cleanups.
2010-06-03 15:32:45 +00:00
008e0e2e0a
Add start of RFCOMM service layer to the incomplete BluetoothHost demo.
...
Reduce the size of the attribute search list from 15 ranges to 8 to save RAM.
2010-06-03 03:58:57 +00:00
3b95b8dedc
Added new VTARGET_REF_VOLTS and VTARGET_SCALE_FACTOR compile time defines to the AVRISP-MKII programmer project to set the VTARGET reference voltage and scale factor.
...
Fixed XPLAINBridge project not correctly reading the XMEGA's supply voltage when reporting back to the host.
2010-05-27 10:36:21 +00:00
670413603f
The EEPROM stream read/write functions now use eeprom_update_byte() instead of eeprom_write_byte(), so that only changed bytes are written to EEPROM to preserve its lifespan.
...
Changed over the AVRISP-MKII and TemperatureDataLogger projects to use eeprom_update_byte() when writing non-volatile parameters to EEPROM to preserve its lifespan.
2010-05-26 11:54:55 +00:00
9c037a952f
The RingBuff library code has been replaced in the XPLAINBridge project with an ultra lightweight buffer to help improve the reliability of the bridge.
2010-05-26 06:15:05 +00:00
776485a6c5
Remove obsolete entry from the Doxygen configuration files.
2010-05-23 08:39:02 +00:00
3e515cdfa8
Short UUIDs are measured in bytes, not bits -- update Service Discovery Protocol code so that it can now correctly match against UUIDs in the service table.
2010-05-20 13:06:04 +00:00
f13bc35a19
Begin processing code for Service Discovery Protocol attributes.
2010-05-17 23:36:05 +00:00
ff61dfa505
Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM instead of the split write-only command (thanks to Tim Margush).
2010-05-16 05:43:03 +00:00
80d85090ba
Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from the last page of FLASH.
2010-05-14 10:11:40 +00:00
34047efc7e
Remove incorrect check for the current device state in the Set Configuration request handler of DevChapter9, which broke Set Configuration requests to the device under most circumstances.
...
Move out the SPI prescaler list to a PROGMEM module-level variable in ISPTarget.c.
2010-05-13 12:57:49 +00:00
571159df1b
Additional fix to the AVRISP-MKII clone project for 256KB AVRs.
2010-05-13 11:14:10 +00:00
cd0093a14b
Fixed AVRISP-MKII clone project not correctly issuing SET EXTENDED ADDRESS commands when the extended address boundary is crossed during programming or readback (thanks to Gerard Sexton).
...
Fixed warnings when building the AVRISP-MKII clone project with the ENABLE_XPROG_PROTOCOL compile time option disabled.
2010-05-13 09:25:17 +00:00
d3c623e1e1
The LIBUSB_FILTERDRV_COMPAT compile time option in the XPLAINBridge and AVRISP-MKII projects has been renamed LIBUSB_DRIVER_COMPAT, as it applies to all software on all platforms using the libUSB driver.
...
Fix Benito makefile which was accidentally changed during testing.
2010-05-13 07:31:27 +00:00
071e02c6b6
Add svn:eol-style property to source files, so that the line endings are correctly converted to the target system's native end of line style.
2010-05-08 03:12:14 +00:00
e331b531c6
Change over instances of "make" in the makefiles to "$(MAKE)" to allow for the make tool to be overridden.
2010-05-07 07:11:25 +00:00
ab8668b14e
Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header.
2010-05-04 11:33:51 +00:00
27f0ba6fc3
Fixed device state not being reset back to the default state if the host sets the address to 0x00.
...
Fixed Set Configuration requests not being stalled until the host has set the device's address.
Fixed possibility of internal signature retrieval being corrupted if an interrupt occurs during a signature byte read (thanks to Andrei Krainev).
2010-05-04 10:07:22 +00:00
eed7d4df6a
Added new ENDPOINT_*_BusSuspended error code to the Endpoint function, so that the stream functions early-abort if the bus is suspended before or during a transfer.
2010-05-03 07:41:22 +00:00
5c0c0327d5
Increase hardware PDI/TPI programming speed to 1MHz in the AVRISP MKII clone project.
2010-05-02 06:18:42 +00:00
a5e79333e5
Switch back to C based timeout ISR in the AVRISP project - assembly version was failing, and only one or two cycles could be shaved off the compiler generated code.
2010-05-02 06:02:54 +00:00
3d28d53c3e
Change AVRISP project's timeout to be interrupt based again, but make the interrupt itself interruptable and use a seperate assembly file to hand-optimize the ISR code.
...
Removed the cast to uint16_t on the set baud rate in the USBtoSerial project, so that the higher >1M baud rates can be selected (thanks to Steffan).
2010-05-02 05:16:34 +00:00
9a1560dc05
Make sure that long reads are aborted early if the connection times out while waiting on more bytes in the AVRISP MKII clone project.
2010-04-30 08:33:21 +00:00
ceb16ee24f
Make sure that the NVM bus/controller busy waits in the AVRISP MKII clone project abort properly if a timeout occurs while waiting for a response.
2010-04-30 08:27:21 +00:00
e977774d4e
Relocate USBInterrupt.c/.h from the HighLevel USB driver directory to the LowLevel directory as it is hardware-dependent.
2010-04-28 08:15:16 +00:00
59c4871f80
USB_Init() no longer calls sei() to enable global interrupts - this must now be done in the user application once all init code has run.
2010-04-28 07:48:26 +00:00
85aaaf84ce
Make AVRISP-MKII clone project's software PDI/TPI mode more robust by keeping track of timeouts while waiting for a Tx/Rx to finish.
2010-04-28 06:33:48 +00:00
5993e1efe7
Added ability to search by Channel PSM to the GetChannelData() function in the BluetoothHost demo.
...
Added new HCI states to properly initialize the bluetooth dongle and retrieve the local BDADDR.
Factored out Bluetooth state information into a new state structure for easy reference in the user application.
Added new StackInitialized() Bluetooth stack callback function.
2010-04-22 14:08:00 +00:00
ee74b4948f
Add information request/response signal handler to the Bluetooth Host demo.
...
Ensure that the AVRISP-MKII project's Windows avrdude compatibility define is named properly in all parts of the code.
2010-04-06 02:48:47 +00:00
fa1a092901
Add user callback function to the Bluetooth host demo to filter out connections from remote devices. Add in ability to reject connections based on their bluetooth device address.
...
Clean up RelayBoard project code.
Make AVRISP project clear the XMEGA target's reset register twice; this does not appear to take affect properly the first time under some circumstances.
2010-04-05 08:09:12 +00:00
c9148f9b47
Added WIN_LIBUSB_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows builds of avrdude at the expense of AVRStudio compatibility.
2010-03-31 09:20:24 +00:00
49b09a2042
Standardized the naming scheme given to configuration descriptor sub-elements in the Device mode demos, bootloaders and projects.
...
Fix errors in the MouseHostWithParser demo from incorrect use of the HID_ALIGN_DATA() macro.
2010-03-22 07:12:25 +00:00
72527867f6
Remove redundant check in the software PDI programming code of the AVRISP project.
2010-03-17 13:07:22 +00:00
9a5ae36a4f
Software PDI mode breaks unless the software USART has 100 cycles between bits.
2010-03-17 11:48:39 +00:00
2b74b517ea
Don't enable the pullup on the target /RESET line in the AVRISP project for PDI mode - clearing the XMEGA's reset control register twice is enough to release it from reset. Possible silicon bug, since the official Atmel programmers have the same issue.
2010-03-16 12:09:22 +00:00
39d56aeffe
Fixed PDI programming mode in the AVRISP programmer project not exiting programming mode correctly (clear target Reset key twice, set /RESET pin to pullup).
...
Add newlines to the MIDI event printf() statements in the MIDI host demos.
2010-03-16 11:47:11 +00:00
071fd8ce53
Revert changes made for the partial port to the AVR32 architecture.
2010-02-24 06:58:23 +00:00
e11fddfe66
Update Temperature board driver to be AVR32 compatible when the ADC peripheral driver is eventually ported. Make architecture includes explicit for both the AVR32 and the AVR8, to make way for future architecture ports.
...
Add SPI driver aliases for the old function names in the AVR8 driver, so that existing code will still compile against the new version.
2010-02-23 03:51:17 +00:00
c24027f3b5
Fixed software PDI/TPI programming mode in the AVRISP project not correctly toggling just the clock pin.
...
Fix broken AVR8 Serial peripheral driver.
2010-02-23 01:03:27 +00:00
d2851b3351
Oops - need to revert changes made to ease testing of the software PDI programming mode.
2010-02-21 22:15:52 +00:00
5e12d436fa
Remove dual ISR for software PDI mode, use a single ISR instead to reduce code complexity.
2010-02-21 22:11:49 +00:00
e322f14620
More fixes to the AVRISP command timeout system so that it should no longer lock up while processing command no matter what the conditions.
2010-02-21 06:26:33 +00:00
12a01ed72d
Increased the speed of both software and hardware TPI/PDI programming modes of the AVRISP project.
2010-02-21 05:44:12 +00:00
10b9394a8b
Oops - missed a few references to the old global TimeoutMSRemaining counter in ISPTarget.c of the AVRISP-MKII clone project.
2010-02-20 12:17:48 +00:00
ce8d0424b1
AVRISP programmer project now has a more robust timeout system, allowing for a doubling of the software USART speed for PDI and TPI programming.
2010-02-19 05:17:41 +00:00
de0ccb3d09
Add NO_VTARGET_DETECT compile time option to the AVRISP-MKII clone project, to disable VTARGET detection on AVR models with an on-chip ADC.
2010-02-13 03:21:28 +00:00
3a2c1db675
Fixed lack of SECTION ERASE command in TPI programming mode of the AVRISP project preventing fuses from being cleared.
2010-02-10 04:07:06 +00:00
ab195ab1da
Added .5MHz recovery clock to the AVRISP programmer project when in ISP programming mode to correct mis-set fuses.
...
Fixed AVRISP project not extending the command delay after each successful page/word/byte program.
2010-02-10 04:02:10 +00:00
35a0fe9384
Fixed USB_GetHIDReportSize() returning the number of bits in the specified report instead of bytes.
...
Moved the USB_GetHIDReportItemInfo() calls into the main report item passing loop in the *HostWithParser demos - it is fast enough not to effect performance, and avoids duplicate code.
Make Webserver project report the LUFA version as part of the HTTP header.
2010-02-09 12:30:51 +00:00
3ab0b3a027
Fix LowLevel Keyboard demo -- accidentally trying to dereference a uint8_t type in ProcessLEDReport().
2010-02-08 03:32:31 +00:00
7ae91099e9
Fix AVRISP-MKII clone project's TPI Chip Erase command processing - ensure erase location is the high byte in the given address space, check NVMBUSY for completion rather than the NVM Bus Enable bit.
...
Change If-Else chains over to switch statements in XPROGProtocol.c for clarity.
2010-02-08 03:16:09 +00:00
15f84bb8f5
New BOARD value option BOARD_NONE (equivelent to not specifying BOARD) which will remove all board hardware drivers which do not adversely affect the code operation (currently only the LEDs driver).
...
Spell-check code/comments in the Webserver/AVRISP-MKII projects.
2010-02-04 02:27:09 +00:00
77e86e7d82
Exlude the "INCLUDE_FROM_*" macros from the individual project's documentation.
2010-02-03 00:57:49 +00:00
53eca61d02
Minor fixups to the documentation and preprocessor tokens.
2010-02-02 13:29:07 +00:00
5687ac7316
Fix TPI mode chip erase code not properly erasing the target memory space.
2010-02-02 04:33:58 +00:00
8d49480891
Oops - new Write Word alignment code in the TPI programming function means that the WriteBuffer parameter is no longer const.
2010-02-02 03:46:49 +00:00
ec6fbb219f
Make TPI writes add a dummy high byte if the data isn't word-aligned.
2010-02-02 03:27:28 +00:00
b736a5ef2b
Make TPI programming protocol program in words, not bytes to satisfy the datasheet conditions.
2010-02-02 03:22:45 +00:00
4d246a82cb
Fixed incorrect values of USB_CONFIG_ATTR_SELFPOWERED and USB_CONFIG_ATTR_REMOTEWAKEUP tokens (thanks to Claus Christensen).
...
Mark the AVRISP-MKII project descriptors as being both Bus Powered and Device Powered.
Copy over file level documentation of the peripheral drivers to the module level documentation.
2010-02-01 12:35:48 +00:00
9e7ffcb014
Make AVRISP XPROG function parameters const where possible.
2010-02-01 05:34:59 +00:00
5f363996e3
Fixed issues with EEPROM and FLASH ISP programming in the AVRISP project.
2010-02-01 03:42:10 +00:00
331e8dece6
Use _delay_us() function in the XPROGTarget.c file to ensure timing requirements are met, rather than a fixed number of NOPs.
2010-01-31 12:33:04 +00:00
75d27f8ef0
Oops - PDI handshake delay was too long, causing the device's /RESET functionality to be re-enabled.
2010-01-31 12:25:53 +00:00
a114878209
Oops - TPI programming is broken in the AVRISP project because the busy-flag check wasn't inverting the result.
2010-01-29 06:02:02 +00:00
872f61ff53
Fix TPI communications in the AVRISP project when bit-banged USART mode is selected.
2010-01-29 05:31:25 +00:00
cec699ac59
Clean up Webserver project - add more Doxygen documentation for the new DHCP client functions and defines.
2010-01-27 13:45:08 +00:00
1aeb5056d6
Ensure TPI enable timing requirements are met in AVRISP-MKII programmer. Remove invalid code in the TPI read/write functions.
2010-01-27 03:45:15 +00:00
2059fd8b1a
Manually pull PDI clock pin high for 1ms before disabling PDI mode in the AVRISP-MKII project, to ensure that the PDI bus is disabled in the target and /RESET functionality restored.
2010-01-27 02:59:54 +00:00
db420853ce
Add Webserver project Doxygen configuration file and overview document.
...
Fix Doxygen configuration files' input file exclusion filters.
2010-01-25 12:46:57 +00:00
74b6993d66
Cleanup and partially fix AVRISP-MKII project's TPI programming support.
2010-01-25 04:13:44 +00:00
857381185d
ADC2 and ADC3 channels do not exist on the U4 series USB AVRs.
2010-01-25 02:15:27 +00:00
5d5e359076
Minor code cleanups, remove TemperatureDataLogger host application's Visual Studio Solution files, add LibHIDNet license files.
2010-01-25 01:27:06 +00:00
b68f7f1649
Added explicit ADC channel masks for the standard set of ADC channels, as the single-ended channel MUX masks are not equal to the channel number on some AVR models. Changed demos to use the new channel masks when using the ADC driver.
2010-01-25 00:52:45 +00:00
dd995683ea
Enhance TemperatureDatalogger project -- add RTC capabilities so that data is logged along with the current time and date. Make logging interval configurable, set by a C# PC host application.
2010-01-24 11:13:23 +00:00
1d2bc47eba
Clean up of the altered XPLAINBridge project.
2010-01-19 05:38:21 +00:00
60fd0ff418
Changed XPLAINBridge project to be both a USB to USART bridge and a PDI programmer, based on the state of a mode select pin.
2010-01-19 05:27:58 +00:00
f3d370a777
Clean up and add more comments to the AVRISP-MKII project. Make sure the SPI_MULTI command handler supports multiple packet responses. Use slightly smaller/faster repeated indirect-load commands when retrieving the PDI target's memory CRCs.
2010-01-17 04:39:33 +00:00
efb6c35778
Update Doxygen configuration files to the latest Doxygen version.
2010-01-06 13:37:29 +00:00
d97db1120b
Added support to the MIDI Class drivers for packed data, where multiple MIDI events are packed into a single USB packet. Added new MIDI Class driver flush routines to override packing behaviour.
2010-01-05 13:52:34 +00:00
7f9f97c792
Update copyright year to 2010.
2009-12-30 23:49:19 +00:00
f5951d1593
Reduced guard bit time in the AVRISP project PDI/TPI protocols to reduce the time needed to reverse the data communication direction.
2009-12-29 14:54:52 +00:00
b1dbd92c32
Fixed AVRISP PDI race condition where the guard time between direction changes could be interpreted as a start bit. Fixed TPI interface lines not being changed correctly when in bit-banged TPI mode.
2009-12-29 14:43:03 +00:00
e1c1c25619
Change the AVRISP project's RESET LINE makefile tokens to AUX LINE, as it is not always used for target reset.
2009-12-29 05:18:16 +00:00
93fe420d89
Minor documentation updates.
2009-12-29 05:08:08 +00:00
4600fd0cb6
Fix TPI NVM Write handler -- AVRStudio sends out writes in page sized chunks, not byte sized chunks.
2009-12-28 07:50:20 +00:00
7c8f4a716f
Add first draft of the TPI NVM commands for reading, writing and erasing a target. Needs testing when physical access to a part is available.
2009-12-28 07:17:21 +00:00
3222f21b84
Add dummy undocumented TPI XPROG parameters to the AVRISP project so that TPI programming mode can be entered.
2009-12-28 02:58:23 +00:00
d4ca7fb44c
Fix MIT license language to make its intent clearer.
2009-12-28 00:34:20 +00:00
d15cbdd490
Fix mistakes in the XPROGTarget.c/.h files for TPI mode software USART clock rate and PDI mode XPLAIN board autoconfiguration.
2009-12-27 14:17:01 +00:00
8301dc553e
Fix references to the renamed AVRISP-MKII project folder.
2009-12-27 12:35:31 +00:00
8ecdc2b144
Rename AVRISP project folder to AVRISP-MKII.
2009-12-27 12:28:29 +00:00
Dean Camera